壳体

Motor vehicles and tractors - the hydraulic jack shell, the exhaust valve, the valve mandril, light trucks around the bridge, CV, axle, torque tube, brake cams, such as roller track.

汽车及拖拉机---液压千斤顶壳体、排气阀、气门顶杆、轻型车前后桥、汽车传动轴、半轴、扭力管、制动凸轮、履带滚等。

Theme is the gerotor pump of Figure 2.9b,where the crescent moulding is dispensed with by using an internal gear with one less tooth than the outer gear wheel.

由于叶片末端是紧靠在壳体上的，所以这里几乎没有渗漏，但是由此叶片末端或者是内壳的磨损却十分严重。

The paper introduces a kind of new spiral feeding equipment for boiler-front coal slurry.It adopts air feed structure and is horizontally installed around the central section of upright wall of furnace tank for boiler.The cooling seal shell and the upright wall of furnace tank are vertically connected each other.

本文介绍一种新型炉侧煤泥螺旋给料设备，它采用加风给料结构，水平安装于锅炉炉膛竖直壁中部四周，冷却密封壳体与锅炉炉膛竖直壁相互垂直联接。

The closed ring confining truss is set along the periphery of the reticulated shell, and the stiffening truss is set in the middle single-layer shell which can take advantage of the architectural shape. These measures resolve the contradiction between overall stability and temperature stress, and also avoid the shell thrust act on the lower concrete structure directly. Besides, these measures simplify the design of the shell bearing and the concrete structure, and the cost of the concrete structure can also be saved.

网壳通过可径向滑动球铰支座与下部混凝土结构连接，网壳周边设置封闭环形约束桁架，中间单层壳体部分利用建筑凸肋造型设置加劲桁架，解决了保证整体稳定和减小温度应力之间的矛盾，同时避免了网壳侧推力直接传递给下部混凝土结构，简化了网壳支座及下部混凝土结构的设计，节约了混凝土结构的造价。

The front end parts include front casing, pedestal, driving shaft assembly, percussion shaft assembly, sliding gear assembly, sliding board, spring, eccentric pin, cam and knob.

它包括前端部件和后端部件；前端部件包括前端壳体，底座，传动轴组件，冲击轴组件，滑动齿轮组件，滑板，滑板弹簧，偏心销，凸轮，旋钮。

The first to use PRO / E software components establishment of the body (body, cylinder head, cylinder pad, cylinder liner, the main bearing caps, Flywheel carcasses, gear Connection Board Room, Shell pump, oil pan, about mounting frame, rear axle oil blocks, etc.) 3D solid model; Then use Hypermesh software division finite element mesh to ensure a good grid quality, and better coordination of the grid between quantity and accuracy of contradictions; Finally using ANSYS software components of a body finite element analysis.

首先利用PRO/E软件建立机体组件（机体、气缸盖、气缸垫、气缸套、主轴承盖、飞轮壳、齿轮室连接板、水泵壳体、油底壳、左右悬置支架、后轴油封盖等）的三维实体模型；然后利用Hypermesh软件划分有限元网格，保证了良好的网格质量，较好地协调了网格数量和计算精度之间的矛盾；最后利用ANSYS软件对机体组件进行了有限元分析。

Using this method to reform reducer shell can t raise cost.

减速机壳体在使用过程中常常出现断裂现象。

Sample,reliable,economic repairing technology of 20A hoist reducer shell wearing are introduced.

介绍了20A绞车减速机壳体磨损后简便、可靠、经济的修复工艺。

The company plans to invest 125 million yuan in science and technology industrial park in Zhangjiajie City Area A land of 120 acres to produce cars, pickup trucks, mini-cars such as small displacement vehicle poor, reducer shell, gear boxes of casting as the basis, eventually Formed mainly to car parts, the casting and machining professional as one of the enterprises.

公司计划投资1.25亿元，在张家界市科技工业园A区征地120亩，以生产轿车、皮卡车、微型车等小排量汽车的差、减速器壳体、变速箱件铸件为依托，最终形成以轿车零部件生产为主的专业铸造和机械加工为一体的企业。

The CDYM-2-02 preselection machine for the gasket of main reducer s shell is introduced, which is fitted on the new flexible assembly line of the main reducer of automobile s rear axle.

介绍了一种新型汽车后桥主减速器柔性装配线中配备的 CDYM-2 -0 2型主减速器壳体垫片预选机。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。