增稠的

All enhancers did not significantly change the transcorneal lag time of ENX. The irritancy of poloxamer and Azone was observed.? The results of in vitro release studies showed that the ENX gel based 3% HPMC K4M and 3%HPMC F4M povided sustained release of the drug over an 8-h period in vitro.Diffusion area has significantly effect on drug release, and pH value of medium and rotation rate have effcet on drug release.However, the diffusion shield has no effect on drug release. The P_ value of the preparation based on 3% HPMC F4M was 1.34-fold of conventional eye drops of ENX.

体外溶出度试验结果表明，以3％的HPMC K4M和F4M为基质制备的ENX凝胶剂的体外释放行为符合眼用缓释制剂的要求；体外释放度影响因素试验结果表明，释放面积对释放度有显著性影响，pH值和转速略有影响，而扩散屏障没有影响；离体角膜透过实验结果表明，以F4M为基质制备的凝胶剂中ENX的表观渗透系数P_(app是对照组的1.34倍，说明F4M与眼角膜的相容性较好，是一种理想的眼用制剂增稠剂，可以在眼用制剂中广泛采用。

The influence of battery formula and technology parameter on the safety performance of mercury-free alkaline Zn/MnO2 button cell was explored. Short circuit test and overdischarge test were used to study the safety performance of battery produced with varied formula and technology parameter. The factors affecting the safety performance of battery were studied. The optimal technology parameters are confirmed as follows: capacity ratio of anode to cathode is 0.91, KOH electrolyte content is 43%, content of Zn22- dissolved in KOH electrolyte is 7%, content of ZnO added in zinc gel is 0.8%1.0%, content of electrolyte added in zinc gel is 40%42%, content of binder added in zinc gel is 1% and the mass ratio of polyacrylate sodium to polyacrylic acid is 64, content of inhibitor added in zinc gel is 0.01%.

摘 要：探讨电池配方和工艺参数对无汞扣式碱锰电池安全性能的影响，采用短路测试和过放电测试的方法研究各种工艺配方下电池的安全性能，通过实验研究了影响电池安全性能的各种因素，并确定最佳的工艺参数分别如下：负极与正极容量配比为0.91，KOH电解液浓度为43%，电解液中氧化锌的含量为7%，锌膏中的氧化锌用量为0.8%~1.0%，锌膏中电解液用量为锌粉量的40%~42%，锌膏中增稠剂用量为锌粉量的1%且其中聚丙烯酸钠与聚丙烯酸的质量比为64，锌膏中缓蚀剂用量为锌粉量的0.01%。

In order to advance the viscosity of acidizing fluid and decrease the reaction speed of acidizing fluid in oil formation,adopt the method of opposite phase emulsim polymerization synthetised an acidizing fluid densifier,it called TP-1,its molecular weight is(800～1100)×10.laboratory findings discovers the acid dissolving time of TP-1 is smaller than 10 min,its dissolv...

性能评价试验结果显示，稠化剂TP-1的酸溶时间小于10 m in，具有很好的溶解能力；TP-1对酸液的增黏作用明显，(4%TP-1+20%HC l)酸溶液90℃下表观黏度达到46 mPa.s，120℃下表观黏度27 mPa.s。同时TP-1表现出较强的耐剪切能力和良好的配制稳定性，有利于酸化措施效果的提高。

This is due to the decrease in solid resin content, caused by their brightness and color hue to the sprasely jiashui of diltue, though, the face of it is in a State of stability and self-crimping polymer binders, once you have the role of epigene will make the segments structure extended until molecular break the business card printing and membership card produce ink film without gloss.

这是由于不流体树脂含量的裁减造不败的，由颜色色相的不浓抹到稠不浓，虽然增火后，暗不天看来处于安定笔直状况的矮不合子拆开料，一旦有内辛的功用会使链段布局扩张直至不合子断裂而使制卡和会员卡制作不不入的图文不朱膜操纵了平泽量）。

The invention provides a method for preparing an epoxy sheet-like mold plastic, which comprises the following steps: thickening the mixed epoxide resin system with diisocyanate compound; strengthening the chopped strand; making the tectorial into non-stick hand and shear epoxy sheet-like mold plastic, that is, preparing the epoxide resin paste and the epoxy sheet-like mold plastic; ripening.

本发明提供的制备环氧片状模塑料的方法是：采用二元异氰酸酯化合物对混合环氧树脂体系增稠，短切纤维增强，覆膜制备成不粘手可剪切的环氧片状模塑料；该方法包括环氧树脂糊的制备、环氧片状模塑料的制备和熟化步骤。

When this product mixtures with other thickner like Guar gum, the viscosity of water solution increases larger or the total content of thickners in water decreases.

与瓜尔豆胶等其他增稠剂复配使用，其水溶液的黏度会有大幅度的增加。因此可以用相对较少的添加量得到相同黏度的水溶液。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。