增大

Objective to study the effect of blood pressure on the enlargement of saccular aneurysm and its mechanism.

目的 研究血压在囊性动脉瘤增大中的作用及其病理机制。

2Compared with control group, the cerebroventricular anfractuosity was longer and lateral fissure was wider on MRI in cerebral MS group. The diameter of brain parenchyma was shorter.

与矫健对比组比力，脑MS患者脑室的量度径线显然增大，脑沟及外侧裂显然增阔，脑实质的量度径线显然缩小。

Through the different assembly of the angle screws and the connective bar, to increase or decrease the fixation angle of the angle screw which as an upholding arm and the connective bar to meet the needs of different lumbosacral angles and hauling screw reducing distance.

通过角度开口螺钉与角度连接棒的不同组合应用，增大或减小作为支撑臂的角度开口螺钉与连接棒之间的固定角度，以满足不同腰骶角及复位距离的需要。

The method which is used to measure and compute moment, yield and turning angle by steel bar gauge is introduced in detail. According to the measuring results, the horizontal critical load of the testing pile is 120 kN. The steel bar gauge measuring results show that the largest moment is located in the depth from 2 m to 3 m under the horizontal load, it transfers to the deeper location with the increase of the horizontal load, and the bend distortion only occurs in the upper of 1/3 pile length.

结合实际工程详细地介绍了利用钢筋计测试水平荷载作用下桩身弯矩、挠度和转角分布的方法，根据桩顶位移和钢筋内力测试结果判定试验桩的水平临界荷载为120 kN；根据钢筋计测试结果可知，在水平荷载作用下，桩身最大弯矩截面位于在地面以下2～3 m处，且随着荷载的增大最大弯矩截面逐渐向深部转移；发生弯曲变形的部分主要是桩长1/3以上的桩体，而其下的桩体几乎不发生变形。

By increasing advance angle of ignition, adopting turbulence combustion chamber with adequate compression ratio, the serious after burning situation can be alleviated greatly.

通过增大点火提前角，采用气流扰动强烈的湍流型燃烧室，并适当增加压缩比，可以有效地改善这一情况。

The downshift of diffraction angle of XRD indicates some precious metals enter crystal lattice of LaMnO3, the crystal sizes of catalysts become larger after precious metal loading; BET and SEM results show sintering happened to catalysts after catalytic reaction.

XRD衍射角向低角度出现了少许偏移，显示负载在表面的贵金属部分进入钙钛矿LaMnO3的晶格结构中，使其晶粒增大；BET和SEM结果表明催化剂在反应后出现了轻微团聚现象。

XRD shows: when the value of x is between 0.1 and 0.3, the alloying thin film remains the structure of hexagonal wurtzite and the angle of (002) diffraction peak becomes bigger as the value of X increases; The photoluminescence spectra at room temperature shows that the PL spectra of the alloying thin film is composed of the stronger UV emission band and weaker visible band, and UV emission peak will have the blue shift with the content of Mg increasing and the visible emission weakened.

XRD衍射测试表明：在0.1＜x＜0.3范围内，合金薄膜仍然保持氧化锌六角型纤锌矿结构，(002)衍射峰位随x的增大向大角度方向移动，在X≥0.3的范围内，合金薄膜的结构则为氧化锌和氧化镁的混合结构；室温光致发光谱表明：ZnMgO合金薄膜PL谱都是由较强的紫外发射带组成，且随着Mg含量的增加紫外发射峰位发生蓝移，同时可见发射增强。

This kind of structure could be obtained byshortening the upper leaves or increasing the leaf angle of elevation.

欲达此目的，可通过缩短上部叶长，或增大叶向值和叶仰角来实现。

The results show that the surface roughness decreases with increase of the inclination angles within the range of 10° to 30°. After the angle approaches to 30°, increase of the inclination angle causes increase of the surface roughness. Furthermore, the effect of inclination angles on cutting speed was investigated.

研究结果表明：工件倾角的大小对已加工表面粗糙度有明显的影响，在倾角为10°～30°时，表面粗糙度随着工件倾角的增大而降低；此后，随着倾角的进一步增加，表面粗糙度有所升高。

The stress and radial displacement will increase with the increment of half cone angle and lead.

螺旋输送器的最大应力强度和最大径向位移均与转速近似地成二次方关系；减小叶片壁厚，沉渣对螺旋叶片作用的正压力所引起的叶片的最大轴向位移增长较快；正常工况下，螺旋输送器的最大应力强度和最大径向位移都随着半锥角和导程的增加而增大。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。