增大

Results show that the incre asing of attack angle,the total pressure recovery chanˉ ges a little and mass flow ratio reduces.However,flow distortionind ex increasers obviously.

结果显示，随着来流攻角的增大，此进气道总压恢复系数变化不大，流量系数逐渐降低，而流场畸变则明显增大。

The results showed that the Shannon-wiener diversity index of forest plant species increased with the increase of the environmental gradient, and the β-diversity indexes of communities showed a liner increase along with the change of environmental gradient.

结果表明：Shannon-Wiener多样性指数随环境梯度的增大而增大，并且β多样性指数与环境梯度呈线性增加的趋势。

Corresponding to the phase inversion point, a sharp peak in pressure gradient also appears at some gas and liquid superficial velocities. It is found that the input water cut of the phase inversion point for three phase flow which is around 40%, is obviously lower than that for two phase flow, which is around 60%.

采用互相关技术分流型研究了油-气-水三相分层流和环状流界面波速特性，结果表明：固定油水比时，SW‖ST流型气-油界面和油-水界面波速、AN‖DO/W流型和AN‖DW/O流型的气液界面波速均随折算气速和折算液速的增大而增大。

The results show that the spreading area of series Ni-P filler metal increases with the increase of brazing temperature, and the spreading areas of Ni-P filler metal is larger than that of Ni-Cr-P filler metal; the shear strength of the brazed joint at room temperature increases with the increase of temperature from 925℃ to 1000℃, and the shear strength of the stainless steel joint brazed with Ni-P filler metal is superior to that with Ni-Cr-P filler metal by 30~40 MPa in the same brazing technology.

结果表明，Ni-P系钎料铺展面积随钎焊温度的升高而增大，并且相同温度下不含Cr的Ni-P钎料铺展面积大于Ni-Cr-P的铺展面积；钎焊温度从925 ℃升高到1000 ℃过程中，Ni-P、Ni-Cr-P钎料钎焊不锈钢接头的室温剪切强度均增大，并且在相同钎焊工艺下，不含Cr的Ni-P钎料钎焊不锈钢接头室温剪切强度优于Ni-Cr-P钎焊接头强度30~40 MPa；Ni-P系钎料钎焊接头高温强度随温度升高而下降，测试温度超过500 ℃时，相同温度下含Cr的钎料能够提高钎焊接头强度0~30 MPa。

The surface tension of polylatexes increased with the increase of polymerization time, and it was shown the use of KCl could increase the surface tension of the latexes.

发现丁苯乳液聚合反应过程中，体系的表面张力增大，加入电解质KCl后，体系表面张力增加幅度增大。

Secondary stress field resulting from valley cutting is basically symmetric about the valley central line hut not of axial symmetry . From top to foot of valley wall , the tangent stress and the width of high tangent stress zone get gradually big , reaching maximum at the valley botton .

沟谷的下切形成的二次应力场除了关于沟谷中线基本对称外，不具备轴对称特征，从坡顶到坡角，切应力高值区内切应力量级和高值区的宽度逐渐增大，在沟谷正下方达到最大，甚至有可能突然增大。

Results CT traits of EH: the symmetric cavitas subarachnoidealis fissure at the top of bilateral lobus frontalis widened at least 5mm; the border looked like "petal"; the front vertical fissure widened at least 7mm, the back vertical fissure was not wide; on patients with serious EH, the bilateral cistern of lateral fossa of cerebrum widened and suprasellar cistern increased while the ventricles of the brain did not increase or increased slightly.

结果 EH的CT特征为两侧额顶部对称性蛛网膜下腔间隙增宽≥5mm，边缘呈&花瓣样&，纵裂前部增宽≥7mm，纵裂后部不宽；严重者可伴双侧侧裂池增宽及鞍上池增大，脑室不大或轻度增大。

Result The skewed parabolic profile is observed in CCA under 1:60 curvature and physiological average Reynolds number. As curvature and Reynolds number increase, the middle of horizontal profile appears sunken and the vertical profile is M-shaped. There are different profile shapes in different localities along the curved pipe.

结果 当颈总动脉的曲率等于1：60 时，在人生理平均流动雷诺数条件下，颈总动脉的速度剖面可用偏斜的抛物面来近似；当颈总动脉曲率增大或流动雷诺数增大时，弯曲平面上的速度剖面中部出现下凹趋势，垂直方向上出现M型速度剖面；沿管轴不同位置上的速度剖面形状不同。

The results indicate that the percent conversion increase, then decrease with the content of MAA increasing.

结果表明，随着甲基丙烯酸含量增大，共聚合转化率呈先增大后减小趋势。

Transmitted torque was composed of magnetic force torque and viscosity torque. Maximal diameter of the actuator disk was key size to improving torque. Torque by unit moment of inertia decreases and viscous power loss increases with maximal diameter increasing.

机构传递的力矩由磁致力矩与粘性力矩构成，圆盘外径是提高传递力矩的关键尺寸；外径的增大会减少单位转动惯量所传递的力矩，增大粘性功率损失。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。