增大

Then, how to determine the shear design values for different structural member and different strengthening location is given out, which could be the reference for design and computation of strengthening structural member by enlarging section method. Fifthly, Full-range shear experiment of two reinforcement concrete arch specimens with strengthening at soffit location by enlarging section method are designed and conducted.

第四，对于增大截面法加固构件，按照极限状态的计算原则，对外荷载作用下的新老混凝土结合面剪力设计值进行研究，提出了不同类型构件及不同的加固部位，新老混凝土结合面的剪力作用设计值的确定方法，可为采用增大截面法加固构件的设计计算提供依据。

The results show that the system belongs to Newton fluid; temperature being increased, the viscosity decreased; surfactant mass fraction being increased, the viscosity increased; the viscosity has the same trend as content of water; their diameters are about 100 nm, its corrosion, density and solidifying point can meet the national standards.

结果表明：微乳柴油体系为牛顿型流体；温度升高，体系粘度降低；表面活性剂质量分数增大，粘度也逐渐增大；粘度的变化同水量的变化规律基本一致；粒径均在100 nm左右；腐蚀性、密度和凝点均符合国家标准；室温时稳定期在6个月以上。

The relationships between male size and spermatophore volume also increased with increasing male size, and the sperm quantity packed in a spermatophore increased with increasing spermatophore volume.

雄蟹的规格和精荚的体积的关系式随着规格的增大，精荚体积增大，精荚中精子的数目也随着增多。

There is an aberration Δφ between the phase retardation of the thermal lens and referenced spherical lens.

在rwp时，ΔΦT相对于参考球面透镜的相位畸变Δφ随r的增大而急剧增大。

Pass to count to Wisterch parameter , and the steel wire is different from the molding tool get in touch with the length, and settle the path the research taking the length work the stabber angle to get under differently pull to stir the term, mold core adoption of best severally why size, combine the best work stabber of research the Cape, and settle the path to take the length nextly steel wire is in the molding tool of have fever to measure, air inside dispel-heat calories, winding dispel-heat on the coil-canister , and its molding tool dispel-heat calories of, and cause the steel wire the temperature difference pass in and outing the molding tool to influence steel wire machine function, under the experiment inside pull to stir the term according to the same race different work stabber Cape half of adoption the Cape(7 degree,10 degree,12 degrees, the best mold Cape, experience mold Cape) settle the path to take the length(2-3 mm,3-4 mm,4-5 mms, theories length, experience length) to proceed to experiment, and get the conclusion, work stabber the Cape then is more big the steel wire get in touch with the length with

通过对Wisterch参数，钢丝与模具接触长度、定径带长度、工作锥角度的研究得到了在不同拉拨条件下模芯采用的最佳几何尺寸，并研究最佳工作锥角、定径带长度下钢丝在模具中的发热量、空气中散热量、卷筒上的散热量及其模具散热量的不同，导致钢丝进出模具的温度差别对钢丝机械性能的影响，在实验中根据同种拉拨条件下采用不同工作锥角半角、定径带长度进行试验，得出结论，工作锥角越大则钢丝与模具接触长度越短，钢丝变形越剧烈，在模具中发热量就越高，导致钢丝出模温度高，使钢丝强度、硬度升高，弯曲、扭转次数降低，并且降低模具使用寿命。在其它条件相同的情况下，定径带越长则钢丝与定径带简壁磨擦增大，使钢丝发热量加大，从而使钢丝强度、硬度略升高，弯曲扭转次数略降低但定径带的增大减小了钢丝变形产生的弹性后效使钢丝出模直径比较稳定。

Results show that with the increase of the apparent gas velocity in the riser,there is little change in negative pressure gradient in the standpipe.

结果表明：随着提升管内表观气速的增加，立管内的负压差梯度变化不大；而随着系统循环量的增加，立管内的负压差梯度以及滑移速度均增大；随着加入热解室内松动气量的增加，立管内尤其是立管上部的压力也随之增大，热解室内无论是移动床流动还是流态化流动均对立管的稳定性影响不大；但当热解室内的压力超过某一值时，立管内的料封很快被破坏，导致系统无法运行。

Passive expiratory flow volume technique was used to examine respiratory system static compliance and total airway resistance.

通气功能、功能残气量、呼吸系统静态顺应性、潮气呼气峰流速随月龄增大而增大，符合婴儿生长发育的规律，1～4月婴儿发育最快。

Results showed that the addition of stearic acid raised the collapse pressures of both mixed monolayers.

结果显示，两体系的崩溃压均随SA的含量分数增大而增大。

And rising inflation uncertainty means that the yield curve still seems likely to steepen bearishly.

此外，通胀不确定性的增大意味着，收益曲线的时间价差将会随之增大。

Distribution of detailed flow parameters such as liquid velocity and stream function were measured by this method.

认为反应器上升段表观气速对液相水平速度和垂直速度均有影响，其中对液相垂直速度的影响更大：表观气速增大，液相最大垂直速度一般增大，但这一变化规律并不是单调的；PIV对折流区的观测反映了该区域流场在气相通入后的最初25 s内的变化历程，流场发展的快慢与进气口的气速有关，气速越大，流场发展得越快。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。