增大

At low HNO3 concentration and dilution factor above 2, 0.1 mol/L DCH18C6/1-octanol extracts very little americium,plutonium and uranium.The distribution ratios of Am、Pu and U increase with the increase of HNO3 concentration in aqueous phase,and decrease with increasing of dilution factor of HLLW.The distribution ratio of extraction of Pu increases with the increase of extractant concentration.

研究结果表明，在低硝酸浓度和较大稀释倍数情况下，DCH18C6对镅、钚、铀的萃取分配比都比较小，并随着水相硝酸浓度的增大而增大，随着模拟高放废液稀释倍数的增大而减小，提高萃取剂浓度会增大四价钚的萃取。

Under the condition that the maximum index change at the core-cladding interface and absorption coefficient were constant, the numerical results indicated that the reflectivity of cross-mode coupling peak between LP_ 01 and LP_ 11 modes varies parabolically with the saturation length of index change.

仿真结果表明，在纤芯和包层边界的最大光致折射率变化量和纤芯吸收因子不变的情况下，随着纤芯折射率变化的饱和长度的增大，LP01和LP11模间的互耦合反射峰呈抛物线形变化，当饱和长度增大到一定值后，互耦合反射峰随饱和长度的增大而逐渐减小并最终消失；同阶LP模的自耦合反射峰随饱和长度的增大而增大。

Using spray to simulate the mist eliminator's actual working environment, at the condition of normal temperature and normal pressure, the relation between separation efficiency and outlet gas velocity, the relation between pressure drop and outlet gas velocity was investigated by experiment.

分离效率先随出口气速的增大而增大至临界点即最大值，然后随出口气速的增大而减小；最佳工况下的分离效率达95%以上。③压降随气速的增大而增大。

Utilized the correlative knowledge of mathematics and theoretical mechanics, the movement measure of the rolling forming of rectangle ring have been studied that based on the ring rolling theory. And the corresponding geometrical models and mathematical models have been established. It was revealed the variation law of ring in the cold rolling process.With the rolling processing, the inside and outside diameters of ring gradually increased with the cures similarly hyperbolic and the augment speed of the inside diameter was obviously larger than the augment speed of the outside diameter. With the rolling processing, the displacement, speed and acceleration of the ring centre gradually increased in the feeding direction in the horizontal and vertical ring rolling mill. With the rolling processing, the moment of inertia which ring reeled its centre and the whirligig of ring gradually increased. It caused the rotary speed gradually decreased. And it was benefit to decrease the circle tolerance and improve the precision of final molding.

本文基于环件轧制理论，运用相关的数学知识和理论力学知识，研究了冷轧过程中矩形截面环件轧制成形的运动测量，并建立相关的几何模型和数学模型，揭示了冷轧过程中环件的变化规律：随着轧制过程的进行，环件的内外径随类似于双曲线的曲线逐渐增大，且环件内径增大速度大于外径增大速度；在卧式轧环机和立式轧环机下，随着轧制过程的进行，环件中心的位移、速度及加速度不断增大；随着轧制过程的进行，环件绕其中心的转动惯量不断增大，导致环件的转速不断减小，这样有利于环件的整圆和最终成形环件的精度。

The electro-optic coefficient as afunction of the photon energy with different values of parameter a and different values of parameter V0 were also plotted.

电光系数的最大值也随着参数a的增大而增大，随着参数V0的增大而减小，表明电光系数将随着量子阱非对称性的增大而增大。

Under the base of it, also considering the characteristics of the multi-channel multistage rimfire gas switch, much study and experiments of the surface flashover along the PMMA insulator and the PMMA housing of the switch were done. Following conclusions were drawn: After introducing PMMA insulator among the board electrodes, the voltage of the discharging of the SF6 drops by 30%. With increasing of the pressure of SF6, voltage of the discharging descends more sharply. With PMMA spacer, the dispersing of the discharging voltage of the gas gap increased as compares to the unbridged gap, such increases in value of the discharging voltage become more obvious with the gas pressure increased.

本文对SF6气体中的沿面放电及影响因素进行了分析，在此基础之上结合边缘点火多级多通道气体开关的沿面绝缘结构特点，经过大量理论分析和电场计算，对有机玻璃支撑绝缘和有机玻璃外筒进行了沿面放电研究，研究结果表明：板电极间SF6气体间隙引入有机玻璃绝缘子后，间隙放电电压平均下降约30%，随气压增大放电电压下降趋势增大，引入有机玻璃绝缘子后放电分散性明显增大，随气压增大，放电分散性呈增大趋势。

The results indicate that in the synchronizing condition the MRF is unyielded, every point of MRF in the flow field has the same angular velocity. Under the slipping condition, with the increase of magnetic field or the decrease of slip speed, MRF may transfer from whole yield to partial yield. When the MRF wholly yields, the angular velocity of MRF increases nonlinearly with its radius, the non-linear distribution becomes more obvious as the magnetic intensity in the working gap increases. When the MRF partially yields, the yield region expands with the decrease of magnetic intensity or the increase of slip speed and the unyield region always reaches the driven rotor. The transfer torque of MRTD increases with the increase of the external magnetic field, but the transfer torque maintains a constant value approximately with the variation of slip speed at the same magnetic intensity.

研究结果表明，在同步工况下，传动装置流场中磁流变液未屈服，各点角速度相同；在滑差工况下，随外加磁场的增大和滑差转速的减小，磁流变液逐渐从完全屈服向部分屈服转变；磁流变液完全屈服时，磁流变液角速度随半径呈非线性增加，工作间隙中磁场越强，流场的非线性分布越明显；磁流变液部分屈服时屈服区域随外加磁场的增大而减小，随滑差转速的增大而增大，未屈服区与主动转子相连；稳态下磁流变传动装置传递的转矩随外加磁场的增加而近似呈线性增大，但在相同外加磁场下，传递转矩基本不随滑差转速改变而改变，表现出良好的恒转矩特性。

The results of numerical simulation suggest that the demisting efficiency increases as droplet diameter and gas velocity increasing and decreases as the mist eliminator plate spacing reducing, and the efficiency of arc-shaped plate with barb mist eliminator is higher than that of polyline-shaped plate mist eliminator. Droplet with a diameter under 20 mm is of low demisting efficiency.

数值分析表明：除雾效率随液滴直径的增大而增大，随进气速度的增大而增大，随除雾器叶片间距的增大而降低；带倒钩的弧形板除雾器比折形板除雾器的除雾效率高；粒径小于20 mm的小液滴脱除效率较低。

The experiment shows that:(1) In certain light intensity and electric field ranges (145～305V/cm) the material Si∶ with a resistivity of 1E4Ω·cm exhibits a current oscillation phenomenon at liquid nitrogen temperature;(2) At a certain electric field,the waveform of the current oscillation is stable and does not change with time;(3) The dependence relation between the oscillation frequency and light-intensity can be expressed by f=f0(L/L0)α where L0 is the minimum light-intensity needed to stimulate oscillation,f0 is the frequency under L0,L is the intensity of the light,and α is a coefficient that increase with electric field;(4) The modulating coefficient K K=(Imax-Imin/Imax decreases as the light increases;(5) The maximum value of the oscillation Imax decreases with the increase of the light-intensity while the minimum value of oscillation Imin increases slowly.

结果表明：在一定光照和电场范围内（276～305V/cm ，电阻率为10.4Ω·cm的材料在液氮温度下显示出电流振荡特性；在一定的电场下，电流振荡波形是固定的，不随时间变化；振荡频率随光照强度的增大而线性增大；调制系数随着光强的增强而减弱；振荡的最大值随着光照强度增大而减小，最小值随着光强增大而缓慢增大。

Single factor experiments were done with the factors including the width of protrusion and the trolley's velocity, which showed that the surface frictional coefficient decreases with the width of protrusion increasing, and doesn't change with the trolley's velocity changing, which was consistent with the results of the orthogonal experiment. A theoretical model of the horizontal projection of a corrugated bionic surface's contact area was built, which showed that the contact area's horizontal projection decreases with width and interval increasing respectively and that the ratio of the contact area's horizontal projection and the vertical load decreases with the vertical load increasing. It indicated that the surface frictional coefficient decreases with the above three factors increasing respectively. Finite element modeling and analysis of interactions of a plate and soils was done using ANSYS, which showed that the plate frictional coefficient is little relative to soil elastic modulus and decreases with vertical surface pressure and that trolley's pull and vertical displacement of bionic surface's control pilot keep constant almost during the plate being pulled. Finite element modeling and analysis of interactions of a corrugated bionic surface and soils was done using ANSYS, which showed that surface frictional coefficient is little relative to soil elastic modulus and decreases with bionic surface's structural parameters and vertical pressure increasing. However, the three factors all didn't affect the surface frictional coefficient remarkably on the condition of 90% dependability. For the first time, bionic surfaces were applied to screw piles, which formed bionic screw piles, and the contrast experiments showed the bionic screw pile had certain resistance-decreasing effects.

建立了波纹型仿生曲面与土壤的接触面积的水平投影的理论模型，表明接触面积的水平投影A随着波纹型仿生曲面突起宽度、两相邻突起间距的增大而减小，接触面积的水平投影与波纹型仿生曲面表面垂直载荷之比随着波纹型仿生曲面表面垂直载荷的增大而减小，进而得出仿生曲面摩擦系数随着波纹型仿生曲面突起宽度、两相邻突起间距以及表面垂直载荷的增大而减小；利用ANSYS软件对平板与土壤的相互作用进行了有限元建模与分析，表明平板摩擦系数与土壤弹性模量关系不大，而随着表面垂直载荷的增大而减小；平板牵引过程中台车牵引力和仿生曲面控制节点垂直方向位移基本保持不变；利用ANSYS软件对波纹型仿生曲面与土壤的相互作用进行了有限元建模与分析，表明波纹型仿生曲面系数在一定范围内基本不受土壤弹性模量的影响，随着波纹型仿生曲面突起宽度、两相邻突起间距以及表面垂直载荷的增大而减小，但在可信度为90％的前提下，三个因素影响都不显著；首次将波纹型仿生曲面应用于与土壤作用方式以挤压为主的螺旋桩，形成仿生螺旋桩，并与普通螺旋桩进行了沉桩对比试验，表明波纹型仿生曲面应用于螺旋桩桩体表面具有明显的降阻作用。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了