增大

The discharge coefficient increases rapidly as the increase of the pressure ratio in the small blade entrance angle while change smoothly in the big blade entrance angle.

在较小几何进气角时，流量系数随压比增大而增大，在较大几何进气角时，流量系数随压比变化不大。

These all make the luminescence efficiency increase and the lifetime of the excited state of Tb〓 become longer.

这些都使配合物发光效率增大，并使Tb〓激发态的寿命增长，即弛豫时间增长，因而光声位相增大。

The results showed that the linear expansivity and apparent porosity of the samples increased with increasing the percentage of matrix materials and aggregate size.

结果表明，随着基质料含量的增加和骨料粒度的增大，试样的线变化率和显气孔率逐渐增大；随着成型压力的增加，试样的显气孔率明显减小，线变化率增加。

From the result it can be concluded that speed difference and crash rates are correlative, and similar empirical functions have been obtained using compound, growth, and exponential curve to fit.

结果表明，大、小车的速度差是引起交通事故的重要原因之一，速度差和事故率之间呈正相关关系，即随着平均速度差的增大，事故率增大。

The coefficient of non-algal particulates is decreasing with the increase of wavelength, which can be described by exponential law.

非藻类颗粒物的吸收系数随着波长的增大而减小，可用指数衰减规律来描述；光谱斜率S较离散，但平均值与文献报道的一类水体S的平均值很接近；光谱截距ad0(λ0)随盐度增大而减小，二者有很好的线性关系。

Analysis and experiment results show that computation quantity of this algorithm does not get too larger with exponentiation getting larger very fast,and may reduce when exponentiation well-selected.

算法分析和实验结果证明，该算法的计算量不会随着指数的快速增大而增大，通过精心选择指数，还可以减少运算量。

The dynamic response of the grain's stress and strain with different grain's inner hole diameter and the ratio of external diameter to inside diameter was analyzed.

计算结果表明，药柱的应力、应变最大值出现在内孔边缘处，且随内孔直径及外径与内径比值的增大而增大。

The results show that the particle's shape of powder is a factor greatly influencing solid loading of slurry,and the solid loading increases with increasing of the dispersant in the slurry.

最后制备出了固相含量为54%的钛合金粉末浆料和形状复杂的坯体。坯体的抗弯强度随气雾化Ti6Al4V含量增加先增大后减小，随着坯体的固相含量增大而减小。

The results show that the microscopical pore structure of the three dimensional orthogonal woven carbon fabric structure perform is composed of body-centered cubes which arranged periodically at spaces. The net structure and shape of the pores of perform are determined by the size and proration of the fasciculus diameter, which are key factors influencing the gaseous permeability and final density of composites. Once the proration of the fasciculus diameters of different directions is determined, the trend of diversification of the permeability followed by pore rate during CVI process and the density of composites are stated, and the permeability increases with the increase of the fasciculus diameter.

研究结果表明：三维正交结构炭纤维预制体的宏观孔隙结构在空间上可以看成是由呈周期性排列的体心立方"晶胞"构成； X ， Y 和 Z 3个方向纤维束直径大小及比例关系决定三维正交结构炭纤维预制体宏观孔隙网络的结构和形状，也是决定反应气体在孔隙中的比渗透率和复合材料最终致密度的重要因素；当 X ， Y 和 Z 3个方向纤维束直径的比例关系一定时，不同预制体在CVI增密过程中比渗透率随孔隙率变化的趋势相同；复合材料的最终致密度一定；比渗透率随纤维束直径增大而略有增大。

The result shows that the main factor to reduce the cutter abrasion is the federate.

结果显示进给是降低刀具磨耗的最主要因素，切削速度增大时会增进刀具磨耗，切削深度增大亦有此趋势，但影响度较小。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。