填满的

Some solutions to the problem are: cutting down on the number of cars, keeping your car in good shape, do not over fill the gas tank and always use clean gas.

解决这个问题的一些方法包括：减少私家车的数量、保持汽车状态良好、不要填填满油箱，以及使用清洁的天然气。

Deadly beauty, the pitcher plant traps insects in its fluid-filled cup, where they drown.

致命的美丽，猪笼草植物随身携带昆虫在它的流动的填满的杯子，昆虫被淹死。

Borneo Pitcher Plant, Borneo, 1999 Deadly beauty, the pitcher plant traps insects in its fluid-filled cup, where they drown.

致命的美丽，猪笼草植物随身携带昆虫在它的流动的填满的杯子，昆虫被淹死。

Much like a recordable CD, your career medium is an empty container waiting to be filled.

与可刻录的CD很相似，你的事业媒介也是一个等待填满的空容器。

The face of the boy who turned, now filling the camera, unmercifully filling the screen, was Jerry's face, but it was blank , as empty as an idiot's.

转过身的那个男孩的脸，填满了整个镜头，无情地填满了整个银幕，那是杰里的脸，但是这张脸上没有任何表情，像一个白痴的脸一样空白。

The face of the boy who turned , now filling the camera , unmercifully filling the screen , was Jerry's face

转过身来的年青人的脸现在填满了整个境头，无情地填满了整个银幕，这正是杰里的脸

The mind is not a vessel that needs filling but wood that needs igniting.

我们的头脑不是一个需要填满的容器，而是需要点燃的木材。

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

If you're logging to a supervised log service, as described in section 2, and the log service fails for any reason: disk full, typo in the run script, log directory configuration error, etc., the pipeline will eventually fill up, causing the service to block, or hang.

如果你使用第二节描述的受到监控的日志服务，日志服务将会因为以下任何原因停止：磁盘满， run 脚本打字错误，日志目录配置错误，等等。而管道将被填满，导致服务被阻塞，或者被挂起。

Stuffed with beef and potato and the possible addition of swede and onions, they are perfect hot out of the oven as the steam escapes when the pastry case is broken.

里面填满牛肉和西红柿，有时还会加点芜菁甘蓝和洋葱，现烤现卖是一大特色，当开启炉门，打开盛馅饼的盒子时，真是热气腾腾，满屋都是馅饼的香气。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了