塔板数

ReduceMain fractionation tower,s press drop can enhance inlet pressure of compressor.At the condition of compress ratio is invariable,it can improve system pressure、increase NTS of stabilization tower、reduce stabilize gasoline C4 ratio、improve system absorbent ability.Generic design can hardly reach the best NTS of absorber,so adding absorber,NTS can obviously increase effect so absorb. Because adding absorber'NTS can reduce system dependence on other factors,and it can not lead to the increase of the energy,so it is the best economic method of improving absorb operation effect. For desorber,double feed stream is a economical means but it need adding the NTS.

降低主分馏塔的压降，可以提高压缩机的入口压力，在压缩比不变的情况下提高系统压力；增加稳定塔理论板数，可以降低稳定汽油中C4的含量，系统的吸收效果改善；一般的设计和吸收塔的最佳板数相距较大，所以改造吸收塔的理论板数，它对提高吸收效果往往最显著，又因为改善吸收塔的理论板数会降低系统对其它因素的依赖程度，而且改善它并不增加能耗，所以改造它对提高吸收效果又是最经济的手段之一；对于解吸塔来说，双股进料的工艺很有经济效益，但它需要增加理论板数来实现。

We designed and simulated the ethylamine separation system using Aspen Plus. The optimal parameters such as theoretical plate number and reflux ratio were obtained.

利用模拟软件Asp-en Plus对乙基胺分离系统进行了设计和模拟计算，得到了各塔理论板数和回流比等设计参数。

In design of rectifying unit to separate toluene-titanium tetrachloride,according to design projects,the theoretical plates of rectifying tower were calculated by the software with graphical calculation of theoretical plate.The tower load parameters in now running float valve tower were checked by the KG-TOWER float valve tower checking softwarel.The packing-tower diameter was calculated by high-effciency structured packings and hydraulic calculation softwocre.The evaluation through calculating data of valv...

在设计分离甲苯—四氯化钛的精馏化工单元中，依据设计任务，通过使用图解法计算理论板软件，计算精馏所用的理论板数；运用KG—TOWER浮阀塔校核软件，对现用浮阀塔进行塔负荷等参数的校核；采用等板数较大的高效规整填料与精馏塔水力学计算软件，来计算填料塔的塔径；通过对浮阀塔和填料塔的计算数据进行评价，得出结论认为选用填料塔设计优于浮阀塔设计。

Deethanizer right choice is the sieve column, so we Tower Drive, plate spacing, sieve number of openings rate Hydrodynamics sieve has done a serious basis, and make a distillation of the stripper and the load performance of the plan, determine the operating point and the operating line.

对脱乙烷塔选择的是筛板塔，因此我们对塔径、塔板间距、筛孔数、开孔率、筛板的流体力学都做了认真的计算，并且做出了精馏段和提馏段的负荷性能图，确定了操作点和操作线。

Base Station type Software versionTypes of carrier frequency board adoptedTypes of combiner adoptedWhether had obtained the network license or notIndoor type or outdoor type Whether the master port is separated from the remote-port The maximum carrier frequency capacity of single cabinet The maximum supportable sector numbers of single cabinetWhether it is dual-carrier frequency board or notMust it be paired configuration if it's dual-carrier frequency board (namely, the type of single carrier frequency station could only configure the dual-carrier frequency on hardware) The maximum achievable configuration of a single station of the single cabinetReceiver sensitivity The maximum expand capacity of a single base station (the maximum number of TRX in configuration / the number of cabinets which is required)(fill in according with the three sectors) Top box transmitted power (given separately a grade one combine and a grade two combine) The maximum output power of amplifier (voice, a single logical carrier frequency) The maximum output power of amplifier (EGPRS, a single logical carrier frequency)Whether it has tower-interfaceWhether it has built-in lightning protectionWhether it support the ultra-long cover / whether it need for software support (give simple description that how hardware and software could achieve this) The supporting condition of EGSM (it should be supported including by the carrier frequency, combiner) Dual-band carrier wave (whether it supports the mixed use of 900 M/1800M in the same cabinet) The commonality of duplicate parts Whether it can built-in transmission unitThe single cabinet size (high × width × deep) Installation method Whether it can place against the wallThe basic frame full-configured weight and the supportable number of carrier frequencyThe expansion frame full-configured weight and the supportable number of carrier frequency

基站型号软件版本号采用载频板型号采用合路器型号是否已取得入网许可室内型or室外型是否是主远端分离单机柜最大载频容量单机柜最大支持的扇区数是否是双载频板如是双载频板，是否必须成对配置(即单载频站型只能硬件配置双载频)单机柜可达到的单站最大配置接收机灵敏度单基站最大扩展能力(最大配置TRX数/需机柜数)(按3扇区填写)机顶发射功率(分别给出一级合路与两级合路)功放最大输出功率功放最大输出功率(EGPRS，单个逻辑载频)有无塔放接口有无内置避雷装置是否支持超远覆盖/是否需要软件支持(简单描述软硬件如何实现)EGSM支持情况(包括载频、合路器均应支持)双频段载波（是否支持900M/1800M在同一机柜内混合使用）备件通用性是否可以内置传输单元单机柜尺寸安装方式可否靠墙放置基本架满配重量及支持载频数扩容架满配重量及支持载频数是否支持基本架与扩容架跨扇区满配功耗满配时重量供电方式机柜进出线方式合路器损耗合路能力：几合一单扇区最大支持几载频合路到一副天线/采用几个合路器单扇区载频达到需要增加一副天线时，是否支持两级合路换以不增加天线如两级合路插损为是否支持基带跳频和合成跳频每单个合路器在从低载频数向高载频数扩容时，是否还需要增加硬件可用性指标MTBFMTTR系统中断服务时间硬件是否支持EGPRS本次报价软件版本号开始支持EGPRS的软件版本号其他特点注： 1 应分别填写出来按照本次报价要求所采用的全部BTS型号和采用的合路器型号 2 列出本报价要求的全部室外型基站与高功放单元

The Shanghai number permanent RJ mold has made the limited companyto be established since 1996, established Wicks the brandseries mold, passes through more than 10 years development, hasestablished the leading status in the national mold profession,unceasingly grows along with the company, we already become from thenumerical control knee bend mold to the numerical control ZTCM and the plate cutter bit omni-directional numerical controlplate work processing equipment cutting tool mold supplier.

上海数恒刃具模具制造有限公司自1996年成立以来，创立了威克斯品牌系列模具，经过十多年的发展，已在全国模具行业确立了领先地位，随着公司不断成长，我们已经成为从数控折弯模具到数控转塔冲模及剪板机刀片的全方位数控钣金加工设备刀具模具的供应商。

The Shanghai number permanent RJ mold has made the limited companyto be established since 1996, established Wicks the brandseries mold, passes through more than 10 years development, hasestablished the leading status in the national mold profession,unceasingly grows along with the company, we already become from thenumerical control knee bend mold to the numerical control ZTCM ＆ the plate cutter bit omni-directional numerical controlplate work processing equipment cutting tool mold supplier.

上海数恒刃具模具制造有限公司自1996年成立以来，创立了威克斯品牌系列模具，经过十多年的发展，已在全国模具行业确立了领先地位，随着公司不断成长，我们已经成为从数控折弯模具到数控转塔冲模及剪板机刀片的全方位数控钣金加工设备刀具模具的供应商。

The Shanghai number permanent RJ mold has made the limited companyto be established since 1996, established Wicks the brandseries mold, passes through more than 10 years development, hasestablished the leading status in the national mold profession,unceasingly grows along with the company, we already become from thenumerical control knee bend mold to the numerical control ZTCM ＆ the plate cutter bit omni-directional numerical controlplate work processing equipment cutting tool mold supplier.

上海急招大中专毕业生，月薪5000，企业订单培养100%推荐就业——赞助商链接上海数恒刃具模具制造有限公司自1996年成立以来，创立了威克斯品牌系列模具，经过十多年的发展，已在全国模具行业确立了领先地位，随着公司不断成长，我们已经成为从数控折弯模具到数控转塔冲模及剪板机刀片的全方位数控钣金加工设备刀具模具的供应商。

The vapour-liquid equilibrium composition on the various plates and the theoretical plate number of the plate tower, reaction volume of multistage continuous stir reactor and the theoretical stage number of multistage extraction can be calculated by this method.

介绍了Excel中填充柄的特点，并对其在板式精馏塔各块塔板上的汽-液平衡组成与理论板数、串联全混流反应器的反应体积和多级萃取的理论级数应用中给出了详细的操作步骤和计算实例。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。