基面

The results show that the brush-plating coating is even and compact from section plane with good toughness and adhesion. The microhardness of the coating is 230.6HV0.5 which is 3 times of cast aluminium substrate. The wear resistance of the coating is 3 times of cast aluminium substrate. But the friction coefficient of the coating is 0.70 which is more high than that of the substrate, which is favorable for the fixed conjugate between the axis sheath and the axis seat of the gear-box.

结果表明，镀层厚度分布均匀、致密，镀层与基体界面清晰，未出现氧化物夹层，镀层的韧性和结合强度均较好；测得碱性铜及铸铝基体的显微硬度分别为230.6、74.2HV0.5；碱性铜的镀制使基体表面显微硬度及耐磨性均提高了2倍多，磨损状况明显改善。

The reason why the crimple appear in the DLC film on the glass substrate was studied. From the angle of enhancing the film-matrix binding force, the influence of the supersonic cleanning to the film-group binding force was studied.

研究DLC膜在玻璃基体表面产生褶皱的原因，从增强膜基结合力的角度入手，考察超声清洗对膜基结合力的影响。

Various [BO6] units exhibit remarkable differece in stability, ion size and ion electrovalence. Therefore, the growth interfaces with electric charges would make a choice among those [BO6]growth units, resulting in the short range of fluctuation in composition and structure at the stage of crystal growth and preparing for the aubsequent formation of ordered domains and other chemical defect clusters.

在基元组装过程中，各种[BO6]八面体基元在稳定性、尺寸大小与电价上的分异致使生长界面对基元有一定的选择性，从而造成了晶体生长时成分与结构的短程起伏，并为有序畴及其它化学缺陷团簇的形成提供了条件。

A schematic model was proposed to illustrate the occurrences of various lithologies and lithofacies associations. The erosional surfaces on siliciclastic mudstones, funnel-shaped structure, and the exhuming of massive cold-seep carbonates exposed might have been occurred concurrently during a tectonic unstable time in SW Taiwan. The deposition of fossiliferous mudstone interfingered with the conglomerate lithofacies, and represented the rapid facies transition from siliciclastic (non-carbonate) into carbonate environment.

综合岩相观察结果，建构一个符合台湾西南部更新世珊瑚礁与基底泥岩接触关系的沉积相模式；其中，基底泥岩顶部的不规则冲蚀面、充填碳酸盐胶结泥岩砾与碳酸岩烟柱的漏斗状沉积，以及块状冷泉碳酸盐岩的出露，可能均为区域地质构造活动时期所造成；至於与含化石泥岩同时沉积的砾岩相，可能均为基底泥岩在快速浅化的过程中所沉积，标志古环境由矽质碎屑快速转变为碳酸盐环境的过程。

The scale-type geometric wear-resistant structure surface is characterized in being made up of a base and the bionic geometric units on the surface. The bionic geometric structure unit is a scale-type structure distributed regularly on the surface of the base, and the distribution density is that: the ratio between the geometric projection area of the scale-type structure on the base surface and the surface area of the base formed by all the edge ends is 50-100%; the scale-type geometric structure unit has a symmetric hexagon shape on the surface; the sides L2/L1=1.0-2.0, L1: 1mm-50mm, and the internal angle Alpha is 120 degree -130 degree, the internal angle Beta is 100 degree -110 degree; the A-A section is subtriangular, and the B-B section is a trapezoid, the height H of the scale-type is 1-5mm.

本发明由基体和其表面上的仿生几何结构单元组成，仿生几何结构单元为在基体表面规律分布的鳞片型结构，鳞片型的分布密度为：其在基体表面上的几何投影面积之和与所有棱端围成的基体表面积之比为50-100％，鳞片型几何结构单元的表面形状为对称六边形结构：边长L2/L1＝1.0-2.0，L1：1mm-50mm，内角α为120°-130°，内角β为100°-110°，鳞片型的A-A截面为近似三角形，B-B截面为梯形，鳞片型的高度H为1-5mm。

The invention discloses an electrochemical method for preparing a hydroxylapatite particle thin coating on the surface of a metal implant, which comprises the following steps: electrolyte is put into a container equipped with a constant temperature heating system and heated to be 30 DEG C to 95 DEG C, and then the temperature is kept; platinum is taken as the anode and evenly distributed around the container, and the metal implant is taken as the cathode, put in the middle of the container and totally soaked in the electrolyte; DC voltage of 2V to 4V is added between the anode and the cathode, the surface of the metal implant has cathode reduction reaction, the pH value is increased and the supersaturation degree of the hydroxylapatite is also increased, so as to crystalize on the surface of titanium; after 0.5h to 5h of deposition, a layer of hydroxylapatite particle thin coating which can be excellently adhered to the matrix metal is formed on the surface of the implant.

本发明公开了一种在金属植入体表面制备羟基磷灰石颗粒薄涂层的电化学方法，在装备了恒温加热系统的容器中装入电解液，并将电解液加热到30～95℃恒温；将铂作为阳极均匀分布在容器四周，金属植入体作为阴极置于容器中间，完全浸没在电解液中，两极之间加直流电压2～4V，金属植入体表面发生阴极还原反应，pH值升高，羟基磷灰石过饱和度增加，从而结晶在钛金属表面；经过0.5～5小时沉积后，在植入体表面即可形成一层与基体金属结合优良的、薄的羟基磷灰石颗粒薄涂层。

With selection, evaluation and the continuous self-pollination, two whole female parent lines were developed. Line A is green base fruit and hairless surface with few convexities, while line B with green base fruit and short thin thorn.

为此，我们于2000年从引进国外10品种，对此进行系统观察、鉴定、评价，通过连续自交的方式，纯化亲本，选育成A型果实基部绿色，果面有稀疏瘤突、无刺毛，B型果实基部绿色，果面有稀疏瘤突，且有短细刺毛的二个全雌性自交系亲本。

One side of a thin elastic base cloth is attached with a layer of machine woven cloth, and the other side of the base cloth is compounded with a PU layer via wet processing of synthesized leather, then the base cloth is dried and molded, and the machine woven cloth is peeled during a coiling process; wherein, the base cloth and the machine woven cloth are fuzzed in a single surface, the fuzzed surface of the machine woven cloth is attached to the non-fuzzed surface of the base cloth by low concentration hydrophilic adhesive, and the PU layer is compounded to the fuzzed surface of the base cloth.

一种薄型、弹性PU合成革的制作方法，先在薄型、弹性基布的一面贴合一层机织布，再在基布的另一面用合成革湿法工艺复合PU层，干燥定型，然后在收卷过程中剥去机织布，其中基布单面起毛，机织布也为单面起毛，机织布的起毛面用低浓度的水性粘结剂贴合在基布的不起毛面上，PU层复合在基布的起毛面上。

Before the process, the glass surface was sandblasted, chemically pretreated and prepared by using PdCl2 as activator.

在前处理阶段采用喷砂和酸蚀结合的方法对玻璃基体表面进行粗化，使用PdCl2对玻璃基体表面进行活化。

The main products are SF-1 (as the base plate of the middle sintering Copper Balls powder, surface modified PTFE); SF-2 (plate as the base of the middle sintering Copper Balls powder, surface modified POM); JDB (For brass, bronze, iron-based body, inlaid solid lubricant); dual-metal (steel as the base for the various models of the surface of copper); production of various enterprises have also filled with PTFE, the curve of bearings, bearing powder metallurgy, by Chun-for the Pistons, Piston Ring, ethylene tetrafluoroethylene ring, ring.

主要产品有SF-1（钢板为基体中间烧结铜球粉，表面为改性聚四氟乙烯）；SF-2(钢板为基体中间烧结铜球粉，表面为改性聚甲醛)；JDB（为黄铜、锡青铜、铸铁为基体，镶嵌固体润滑剂）；双金属（钢板为基体表面为各种型号铜）；企业还生产各种填充四氟带、曲线轴承、粉末冶金轴承、减震器活塞、活塞环、四氟乙烯密封圈、环。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新