基面

By three-dimensional nonlinear finite element method, the breaking mode and stability of 3B dam block of Baise RCC gravity dam is studied, and the breaking mode and stability safety factor of the 3B dam block on a datum plane with steep slope are figured out corresponding to overload method and synthetic method respectively.

采用三维非线性有限元法，对百色RCC重力坝 3B坝段进行破坏模式及稳定性的研究，确定出含陡坡建基面 3B坝段在超载法和综合法下的破坏模式及稳定安全系数。

Luminescence properties of basal plane dislocations in 4H-SiC are studied by means of cathodoluminescence and defect selective etching.

本文利用阴极荧光和选择性刻蚀的方法对4H-SiC同质外延材料中基面位错的发光特性进行了研究。

Does not change the color of the base surface to maintain original construction.

不改变基面颜色，保持建筑原貌。

Acrylic acid that the cardinal plane reinforces a tier is that rolling direct cement sharpening agent (SRA-01) Tu follows the evidence air temperature on surface, but adds appropriate amount addition Shimizu commixture dilution with acrylic acid in clean base of drying.

丙烯酸基面加强层是用丙烯酸水泥加强剂（ SRA-01）直接滚涂于干燥洁净的基面上，跟据气温可加适量添加清水混合稀释。

The arch dam is a structure with many redundant, and its base surface is a spatial curve with the complex shape usually .

拱坝是一个高度超静定的结构，其建基面一般为形状复杂的空间曲面。

A conic section whose plane is not parallel to the axis,base,or generatrix of the intersected cone.

圆锥的一部分，其切面既不平行于轴和基面，也不平行于圆锥母线

Langle a\rangle$ dislocation generated during creep may cross--slip from one of non--basal plane to another non--basal planes.

其中 a 位错通过位错分解反应可由一非基面交滑移至另一非基面。

The cross-sections of plant tissues were rapidly transferred to aluminum foil-coated microscopic sides for reflectance mode analysis in FT-IR microspectroscopy with imaging, mapping, ChemiMap, and line scanning techniques.

接著植物组织之横切面薄片被迅速转移至铝箔包覆显微载玻片上，作为傅立叶转换红外线显微光谱仪在全反射模式下，运用光学影像、面扫描、化学官能基面像化及线扫描等技术分析使用。

Fig. 4 Density, basal area, total tree biomass and percentage of belowground biomass P

2， 这是由于在此期间最初在群落中占据优势的藜蒴大量死亡，死亡植株的基面积大于增加的基面

To presents the methods of designing and making circuit board for experimental teaching by computer, laser printer and heating roller, which are the methods of designing and making printed circuit board on one-side copper plate and the circuit drawing, on insulated epoxyresin base.

介绍了利用计算机、激光打印机和制板机设计制作实验教学电路板的方法。即在单面覆铜板的铜面设计制作印制电路板，在绝缘玻纤环氧树脂基面设计制作电路原理图。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。