基本参数

As a power device in the water-propulsion system, which is widely used in the ocean tramp and amphibious tanks, etc., CRAFP can increase the main body propulsion and propulsive speed greatly.

对旋轴流泵作为动力装置应用于喷水推进系统，在系统空间和其它几何参数基本不变的条件下，可以大幅度提高主体推力和推进速度，可应用于远洋货轮、水陆两栖战车等重要场合。

The welding robot task programm system makes up with condition model building organ, task programmer, parameter arithmetic organ, task planning organ and sensor information processor. The task programm function is implemented.

开发的由环境建模器、任务编程器、参数运算器、任务规划器和传感信息处理器组成的专用焊接机器人任务级离线编程系统，实现了基本的任务级离线编程功能。

Very good results were obtained in logP modeling for carboxylic acid, ethanol, phenol, aldehyde, ketone, ether, ester and amine. A QSPR model of logP for many kinds of substances was established by multi-linear regression with the first-order molecular connectivity valent index 〓 and the number of hydrogen bonds N as two patameters.

利用这两类结构参数，分别建立了脂肪族羧酸、芳香族羧酸、醇、酚、醛、酮、醚、酯、胺类物质的疏水性常数定量模型；在此基础上，建立了包含8类基本有机物144种物质的疏水性常数的定量模型，并提出logP的简化模型。

According to the acoustic model of piston slap noise, how the parameters affect the piston slap noise at different rotate speed was discussed. And those parameters were piston clearance, piston pin offset, connect rod ratio, piston skirt stiffness, crank shaft offset, height of piston's gravity center, total length of piston skirt, vertical position of piston-pin axis and under part length of piston skirt.

借助建立的活塞拍击噪声理论声学模型，深入探讨了配缸间隙、活塞销偏移量、连杆比、活塞裙部刚度、曲轴轴线偏移量、活塞质心高度、活塞裙部总长度、活塞销轴线竖直方向位置和活塞裙部下段长度等主要影响参数在不同的转速下对活塞拍击噪声的影响规律，初步总结出活塞低拍击噪声设计和改进的基本规律。

Some valuable conclusions were drawn and shown as following: Three models were brought forward, i.e. 6DOF rigid-connected model, 8DOF rigid-jointed model and 12DOF non-rigid connected model. The basic dynamic properties of the system, the relative motion between parafoil and payload, and some geometric parameters'effects on the system dynamics were analyzed and summarized.

分别建立六自由度刚性连接模型、八自由度刚性铰接模型和十二自由度非刚性连接模型，着重分析了系统的基本运动特性、回收物-伞体间的相对运动特性，以及主要设计参数对系统性能的影响；并将不同复杂程度的模型进行对比，分析了各种模型的特点和适用范围。

The basic technical process and main processing parameter of investment casting nozzles are presented in detail.

重点介绍了喷嘴的熔模铸造基本工艺过程和主要工艺参数。

Based on Wavelet Packet Analysis and Smoothed Pseudo Wigner-Ville Distribution, the experiment data is time-frequency analyzed. The experimental results indicate that the amplitude of the laser-induced acoustic waves increases with the laser energy; the frequency coverage is from 0 to 150 KHz, and in the meantime there is a peak located at about 25 KHz. In addition, the spectrum and the peak of frequency are basically stable in spite of the change of laser energy and target texture.

从基本的空泡动力学理论出发，推导了空泡各特征参量之间的关系，进而对空泡动力学模型进行了修正；采用有限差分法对空泡脉动进行数值模拟，得到了空泡脉动特性随液体粘性、空泡含气量、表面张力以及可压缩性的变化规律；实验上采用光偏转测试装置探测了激光空泡脉动以及空泡溃灭的细节过程，进而分析了液体粘性和作用激光能量对空泡脉动周期、泡半径及泡能等特征参数的影响。

As an application,generating quasi arc-length parameterization of PH curves is also discussed.

在CAGD中，曲线曲面一般用多项式或有理多项式表示，因此求解多项式函数的反函数是CAGD中的一个基本问题，它在曲线的准弧长参数化、曲线隐式化、曲线求交等问题中都有非常重要的作用[1-2]。

By using the basic principle of soil hydrodynamics,this paper designs the indoor experiment of soil water infiltration under surge furrow irrigation ,and in the light of the influence of the different water-supplying times,circulating ratios and periods on the soil water infiltration process,determines some parameters related to the soil water movement.

应用土壤水动力学的基本原理，设计了波涌沟灌条件下水分入渗的室内试验，针对不同供水时间、循环率及周期对土壤水分入渗过程的影响，测定土壤水分运动有关参数。

According to determined and analyzed of parameters of the wood transverse section micrograph, established of the recognition algorithm and programmed of wood recognition method, the results showed that the wood recognition method was feasibility based on the image manipulation.

通过对木材横切面显微图像量化特征参数的提取与分析、基于图像分析的判别匹配算法和判别程序的建立，结果表明，以基于图像分析的方法达到木材判别的目的是基本可行的。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。