基侧的

The four sets of stator bars including those retired from three large generators and the standby bar subjected to Dynamic Mechanical Analysis, Scanning Electron Microscopic and optical microscope observation. It was revealed from DMA that the peak value tan d m of mechanical loss thermogram tan d ~ T shift toward a higher temperature and a lower amplitude, indicating that the amount of movement monomers diminished greatly in the insulation aging process, the tan d 195, increased very slightly with the service time of insulation, showing the degrading of bonding properties at interface, and the presence of more defects in insulation. The observation of SEM and optical microscope showed that more and more voids appears in insulation, and delamination was formed due to development of voids in aging process.

对不同运行年数的线棒进行了 DMA 、 SEM 、光学显微镜等微观分析试验，动态力学分析发现(参见 Hao et al， CEIDP， 2002：404)，力学损耗温度谱 tan d ~ T 的峰值 tan d m 随老化时间向高温、低值方向移动，表明促成环氧发生玻璃化转变的活性侧基或发生局部运动的活性链段减少，分子链的刚性增强；195℃的力学损耗 tan d 195随老化时间有缓慢增大的趋势，表明有更多的能量耗散在界面处，界面的粘合性变差，甚至由于界面粘结不良出现微观缺陷； SEM 和光学显微分析发现(参见 Hao et al-2， IEEE DEI， 2003)，老化后的绝缘气隙增多，随着老化时间气隙不断扩展或相互连通，绝缘逐渐分层。

In order to determine further the profile of scrolls,the structural characteristics of superchargers with double-sided scrolls were analyzed and the principle of determining initial involute angle s was presented on the conditions of definite initial involute angle s,radius of base circle,and depth of scrolls.

在渐开线起始角、基圆半径和涡旋齿深度确定的条件下，为进一步确定涡旋齿的齿形，对双侧涡旋增压器的结构特征进行分析，提出始端渐开角的确定原则。通过吸气腔和排气腔的容积计算，结合回转角与渐开角的关系，给出涡旋齿始端和终端渐开角的计算方法。结果表明：该计算方法能较准确地确定涡旋盘的结构尺寸，从而可估算出整个压气机的尺寸是否满足汽车上有限的安装空间

heological properties at a low shear rate range(10-2-10s-1) and the glass transition temperatures for PEK-C with different moleCular weithts have been studied by using a cone/plate rheometer and DSC' The activation energy for melt flow increases with Mw The dependence of Tg on molecular weight exhibits two linear range and the value of nitersect agrees with the critical molecular weight , Mc' which is first reported for PEK-C' Mc value obtained according to η0 is about 8× 104 g/mol and the relation between Mc and temperature was dis-cussed.

用锥权流变仪及DSC的方法研究了5种不同分子量的酞侧基聚芳醚酮在低剪切速率区（10－2－10s－1）的流变行为及其分子量与玻璃化转变温度的关系。结果表明，样品的粘流活化能随分子量的增加而增大，Tg随分子量的变化是二个线性区，其交点值与所求的样品的临界分子量值相对应。利用测得的零剪切粘度值（η0）首次求得了PEK—C的临界分子量值。同时也讨论了Mc与温度及η0和Tg与分子量的关系。

To present an adhesive sheet roll for wafer processing excellent in storage stability, radiation curing property, and low contamination to wafer.

一种保存稳定性、放射线固化性以及对晶圆的低污染性优异的筒状晶圆加工用粘合片，是将由基材薄膜、放射线固化性粘合剂层、以及脱模薄膜按顺序层叠而成的层叠薄膜，多重缠绕而形成的筒状晶圆加工用粘合片，所述基材薄膜和/或脱模薄膜的与放射线固化性粘合剂层接触的面的另外面侧表面的轮廓算术平均偏差为1μm以上，且所述放射线固化性粘合剂层中所含的自由基聚合抑制剂的重量低于1000ppm。

In studies of interaction among pile, platform that above it and surrounding soil, this paper employ the concept of plate element to simulate the loading character of platform, and employ the concept of solid element to simulate the character of pile and soil, using the finite element method after understanding the geometry properties of pile, soil and the platform. Analyzing the loading properties of the three entities above and their deformation, this paper also employ a special element, Penalty Element. The introduction of penalty element of this kind has served to guarantee the join harmony of displacement between solid element and plate element, thereby effectively resolving the join problem between platforms, pile that support it and surrounding soil.Considering significant property difference between pile material and its surrounding soil, there may be much shear stress on their contact interface produced under vertical load, thus causing displacement or fission. Therefore it is necessary to adopt one special constitutive law of this kind of contact interface, which can reflect its feature of loading and deformation thoroughly. On the basis of the deformation feature and constitutive laws of some contact interface obtained by Zhang Dongji and people concerned through some single-shear experiments on contact interface between structure and soil, this paper employ one pile-soil three-dimensional constant thickness contact interface model to simulate the " slide" taken place on the interface between pile and its surrounding soil. With this kind model, this paper has also created one finite element model, which can be applied to perform finite element calculation and analyze the pile-loading feature, and deduced its element stiffness matrix.

在承台-桩-土共同作用中，考虑桩与承台的几何特性，采用有限元方法，用实体单元模拟桩土，用板单元模拟承台，更具体地分析桩和承台的受力特性和变形，而且还采用罚单元—既实体单元与板单元之间连接必须满足变形协调条件，来有效地解决了承台与桩土的连接问题，且在桩土共同作用中，由于桩体结构的材料性能与周围土层性质相差较大，在竖向荷载下有可能在其接触面上产生较大的剪应力从而导致错动或开裂，因此，为了充分反映桩土接触面上的受力及变形特征，应采用一种桩土接触面特有的本构关系，即利用张冬霁等人关于结构与土体接触面单剪试验所得到的接触面变形特征及其本构关系，引入桩-土三维等厚度接触单元来模拟桩与桩侧土之间的&滑移&，在此基础上建立可用于桩基承载性状分析的有限元计算单元模型，并推导出了各单元的刚度矩阵。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。