垂直的位置

023 The centre of the footrest shall align on the same perpendicular to the ground as that of the fore-most point of the saddle and rearmost points of the handlebar.

脚蹬中部的位置要与车座最前端和车把最后端一样垂直於地面，脚蹬的前部要能持久地固在距离跑道240公厘的地方。

Results:① The distance between handle of malleus and stapes head was(2.38±0.19)cm(2.00～2.70cm), the point selecting for measuring was outer margin of handle of malleus and stpes head.②The cross section form of one_third of the handle of malleus at the end, was triangle, the anteroposterior diameter of handle of malleus was(0.79±0.12)mm, the exterior and interior diameter was(0.58±0.10)mm at the crook point,the angle of line of manubrium mallei laid(83.24±8.33)°(66～98°)posteroinferior to arch of zygoma.③The long axis of prosthesis formed(27.60±1.75)°(24.6～30.2°)angle with the perpendicular of stapes.④The dependablity between the malleus_stapes distance and transverse diameter of tympanum, the location of umbo in tympanic membrane, the diameter of manubrium mallei, angle of line of manubrium mallei and arch of zygoma were not statistically significant.

结果：①锤_镫距离最短为(2.38±0.19)cm(2.00～2.70cm)，测量点为锤骨柄末端1/3处外缘和镫骨头；②锤骨柄末段1/3横断面形状接近三角形，弯曲处前、后方向直径为(0.79±0.12)mm，内、外方向直径为(0.58±0.10)mm；锤骨柄与颞线的成角为(83.24±8.33)°(66～98°)；③赝复物长轴与镫骨垂直方向成角平均为(27.60±1.75)°(24.6～30.2°)；④锤_镫距离与鼓室横径、鼓脐在鼓膜上的位置、锤骨柄直径、锤骨柄的方位的可能相关因素之间相关性检验无统计学意义。

Its control object is a plate with two mutually perpendicular shafts, and its purpose is to balance a freely rolling ball in a specific location or to make it move following the specific trajectory on the plate.

其控制对象是具有2个相互垂直的旋转轴的板，目的是让一个自由滚动的球能够平衡在板上的特定位置，或使其沿着特定轨迹运动。

4 Components in the guide ring seat surface, and to maintain stem vertically in a clean work surface; 4.5 Lubrication and installed on top of the spring washer bearings and bearing connecting rings, and lubricating the bottom of the spring washers, valve cover and gasket components will be placed in position inside the valve cover; 4.6 will regulate the bolt lock nut bolt screw to adjust the top.

4.4 将组件座于导环面上，并保持阀杆垂直地处于清洁的工作面上； 4.5 润滑并在顶部弹簧垫圈上安装轴承和轴承连接环，和润滑底部弹簧垫圈，将阀盖及垫圈组件放在阀盖内的位置上； 4.6 将调节螺栓锁紧螺母拧到调节螺栓的顶部。

To establish the cutting lines, place marked pieces of tape on the wall to mark the horizontal and vertical cutting lines. Lay a metal straightedge between these lines.

为了建立切割线，可以将做了标记的胶带贴在墙上用来标识垂直和水平切割线的位置。

Meaning that advertisements will appear on the right side of the screen in vertical bar, which cannot be removed or dragged minimize to hidden position.

也就是说，广告会出现在屏幕右侧的垂直酒吧，不能删除或减少拖了隐藏的位置。

Prior to registering the mandibular neutral zone, reestablish an appropriate vertical jaw relationship, and deprogram muscles responsible for mandibular posture.

在记录下颌中性区前，很有必要找到颌骨在垂直向上合适的位置，放松负责下颌运动的肌肉

When using an , you don't only need to adjust the perpendicularity between end plane and axes, but also need to adjust the position of four jaws to make the center of workpiece's front face coincides with lathe spindle.

使用四爪卡盘时不仅要调整端面与轴线的垂直度，还要调整四爪的位置，使工件前端面的圆心与车床主轴重合。

The purpose of this study was to examine the maximum value of pulling-force, momentum, ground reaction force, net muscle joint moment, the changes of muscle power on raising movement after sitting by different sitting distance patterns, which was measured from feet to a supposed vertical point on hip joint (25cm.35cm.45cm) during Tug-of-War.

中文摘要本研究针对拔河坐地起身动作，以足跟至髋关节点垂直地面位置的不同坐地距离（25公分、35公分、45公分）探讨起身动作之最大拉力值、冲量值、地面反作用力、净肌肉力矩、肌肉功率的变化，藉以了解坐地距离之变化对起身动作之生物力学影响。

Methods: The terminal position of the muscular contraction path and centric relation position with different vertical dimension were recorded for ten edentulous patients with gothic arch.

采用哥特式弓描记装置测量10例无偏侧咀嚼的牙列缺失患者不同垂直距离下肌力闭合道终点位与正中关系位在平面上的位置关系。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。