坡

The magnetoresistance effect at room temperature in oblique-incident vacuum evaporated permalloy film s was studied.

研究了斜入射蒸镀的坡莫合金薄膜在室温下的磁电阻效应。

Electrodeposited Ni-Fe permalloy foils was annealed under hydrogen atmosphere at 850,1 000 and 1 150 ℃ for 5 h, respectively.

对电沉积得到的Ni-Fe坡莫合金箔，在氢气气氛下进行退火处理，退火温度分别为850，1000和1150℃，保温时间均为5h。

The device consists of a square planar coil , a spring support structure, and permalloy magnet film.

研究了平面线圈对坡莫合金磁体的微小作用力，并用有限元模拟软件ANSYS ，对该作用力进行了模拟分

It was found that the pemeability of the dust core was almost a constant in the frequency range from 1KHz to 100KHz,and the quality factor Q of dust core increased with increasing frequency.It was also found that Q became higher at the frequency over 50KHz in comparison with that of permalloy in higher frequency.

结果表明，在测量的频率范围内(1KHz-100KHz)，该粉芯的磁导率几乎不随频率变化而变化；粉芯的品质因数Q随频率的增加而增加，在较高频率时有着比坡莫合金粉芯还要高的值，具有应用价值。

Crystal size of the iron based alloy foil is less than 10μm, while the crystal size of the nickel based alloy foil is about 2μm. Results show that the electrodeposited Fe-Ni foil has better magnetic properties than conventional milled Permalloy 1J79 foil.

实验表明：电沉积铁基合金箔晶粒小于10 μm，电沉积镍基合金箔晶粒大小在2 μm左右；电沉积Fe-Ni合金箔是一种性能良好的软磁材料，其基本磁性能优于传统熔铸-轧制坡莫合金1J79。

Keywords magnetic material;soft magnetic material;hard magnetic material;vacuum heat treatment;vacuum furnace;permalloy;silicon steel;deoiling

磁性材料；软磁材料；硬磁材料；真空热处理；真空炉；坡莫合金；硅钢；脱油

The anisotropic magnetoresistance and saturation magnetic field of the Permalloy thin films (Ni0.81Fe0.19) sputtered on a nonmagnetic (Ni0.81Fe0.19)0.66Cr0.34 buffer layer were measured. The AMR variations of the films after annealing and the size effect of the AMR stripes after etching were emphatically studied, and a qualitative analysis was proposed through a statistic model. The simulation results agree with the experiments.

研究了以非磁性（Ni0.81Fe0.19）0.66CR0.34薄膜作为过诞层的坡莫合金Ni0.81Fe0.19薄膜的磁电阻效应和饱和磁场，分析退火处理对样品饱和磁场的影响和经刻蚀后的磁电阻效应膜线的尺寸效应，并建立一个统计模型定性分析了其性能变化的机理，计算结果符合实验。

The process includes dry etching the protecting layer of AMR film; wet etching the permalloy layer of the AMR film; and dry etching the transition layer of the AMR film.

一种多层膜的干湿结合蚀刻方法，包括：干法刻蚀各向异性磁电阻效应薄膜的保护层；湿法腐蚀各向异性磁电阻效应薄膜的坡莫合金层；干法刻蚀各向异性磁电阻效应薄膜的过渡层。

Then the MEMS solenoid type electromagnetic actuating and novel, frictionless and wear-free, and simple structure are designed for fiber-deflecting type MEMS VOA: One of the two coupled single mode fibers is completely fastened in one of the three aligned U-shaped grooves while the deflectable fiber is partially fixed in another groove with a long front section suspending over the wider groove as a cantilever beam. The two fibers, any one for input and the other for output, are well aligned initially so that the insertion loss is very low. Beside the deflectable fiber is a solenoid microactuator with a U-shaped permalloy core attracting a permalloy piece glued on side of the fiber cantilever so that the fiber is deflected and the optical power coupled between the fibers decreased continuously. Using MEMS solenoid as a continuous actuator and the novel structure of VOA are not seen in literature.

为光纤偏移型MEMS可变光衰减器设计了MEMS螺线管电磁驱动方式以及新颖的避免了静摩擦、磨损而且简单的整体结构形式：在硅基片的三段V形槽结构中，将两个对接单模光纤之一完全固定在基片上，只将另一根光纤的稍后部位固定于基片上而使其前端的一定长度悬空，形成一个悬臂梁结构；初始对准后两根光纤之间的光传输损耗很小；通过U型铁芯MEMS螺线管吸引固定于光纤悬臂梁上的坡莫合金片，驱动光纤悬臂梁连续偏移以使两根光纤之间功率传输系数连续变化，从而达到光功率连续衰减的目的。

Carbon encapsulated permalloy nanoparticles were prepared with a pyrogenation anneal method. Nanometer magnetic fluid was obtained by mechanical ball milling, using oleic acid as the modifier and kerosene as the carrier liquid.

用热解－退火法制备了碳包覆坡莫合金纳米粒子(carbon encapsulated permalloy nanoparticles， CEPNPS)，选用油酸为表面活性剂，煤油为载液，采用机械球磨法制备出CEPNPS磁流体。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。