均匀分布

The asymmetrical distribution of temperature and fuel component affects the distribution of current density.

温度和燃料组分的非均匀分布直接影响了电流密度的分布。

Distributing the index finally demand and application of rate of even distributinging attaint arrive in general model, through calculating exemple undertake sensitivity is analysed.

最后将指数分布需求和均匀分布损坏率应用到一般模型中，通过算例进行敏感性分析。

The effectivity of Bayesian statistical method on the estimation of bimodal distribution is shown by numerical simulation.

较详细介绍了贝叶斯统计方法在海浪方向谱估计中的应用，指出先验分布的不同对估计结果没有影响，由于均匀分布与最大熵原则相对应，使其具有某种特殊性。

Grout must be supplemented in time to ensure the gap between soil and pipe to be stuffed.

注浆工艺的合理性对管道顶进施工的顺利实施有重要的意义，并就注浆工艺的改进提出了以下要点：及时补充压浆，力求使地层与管道结构间的缝隙始终由浆液密实充填；及时调整注浆压力，力求使其与管段所在位置的水土压力值相等；注浆孔在管段横剖面上均匀布设，以使注浆压力沿管道周边均匀分布；对位于顶进管道前端的数节管段，宜每节都设注浆孔，使可及时注浆和补浆。

The results show that the diffraction spot of a spectrally dispersed beam becomes larger and its near-field uniformity is improved,while there exists area where the intensity is nearly even within the far-field spot.

模拟结果表明，光谱色散会使光束衍射光斑变大，近场空间强度均匀性改善，而远场光斑内部存在光强接近于均匀分布的区域。

As the thermal radiation of coating surface on Low E glass is strongly influenced by its spectrum, the nongray band model in diffusing enclosure was used to numerically simulate the surface radiative characteristics of Low E glass in combination with the glass properties of absorptivity and transmissivity.

由于建筑节能的需要，低辐射率玻璃被大量地应用于建筑物等公共场合。为保证安全使用，这些玻璃必须经过物理钢化处理，即将玻璃制品加热到其转变温度Tg 以上 50～60°C ，然后在冷却介质中急速均匀冷却，使玻璃表面生成均匀分布的压应力层。

The characteristics of density bands of Porites coral from Meiji reef in Nansha area are revealed by X-radiography of coral slabs and periodical changes of δ^18 O and δ^13 C in the skeletons.

结合珊瑚骨骼X射线照片和δ^18O、δ^13C的年际变化，对南沙群岛美济礁滨珊瑚骨骼岩心的密度条带进行了分析，发现其密度带变化模式多样，初步可归纳为如下3种类型：(1)宽度相近的高低密度条纹均匀、相间地排列，一对高低密度条带平均宽约4mm；(2)在骨骼主生长轴上由近于均匀分布的细密度条带组成。

The mainly characteristic of it is the high efficiency intermingles and homogeneous. Not only the microstructure but also the second phase is uniform.

其主要特征是均匀性掺杂，不仅反映在纳米电子发射材料的微观结构方面，而且表现在第二相的更加均匀分布方面。

There are several reasons for this: injection technology (usually featured by 128-cavity moulds) makes it extremely difficult to maintain uniform temperatures, to ensure uniform distribution of plastic etc. So outgoing pieces are not all the same and, because bottling lines are ever-faster, any downtimes caused by cap quality problems can inflict economic damages on the producer that are much higher than the unit cost of the individual cap.

这是有：注射技术的若干（通常是由在128腔模具）的原因使得很难保持均匀的温度，以确保即将离任件，所以不是所有的一样的，塑料等均匀分布，因为瓶装生产线是不断更快，任何停工时间造成的帽子质量问题可以对生产造成的是比个人帽的单位成本高得多的经济损失。

Optimization method is applied to the layout design of mechanisms on trolley in order to maintain an even distribution of optimization design on an example a trolley with given wheel base and track gauge ,using even distribution of wheel loads as an objective funtion and condition of a signle hook lifting trolley as restrictive condition

桥式起重机的大车设有起升机构和小车运行机构，为使小车轮压呈均匀分布，应对大车的机构布置进行优化设计，以知大车轨迹和轴矩为例，以车轮轮压均匀分配为目标函数，按单钩起重大车的条件提出约束条件，对优化设计的结果进行分析如下

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。