在腔中的

Check the bolt and nut and filling press cover, it it become flexible during the transport or store, screw down it.

内腔进行去湿处理并检查各连接部位的螺栓、螺母和填料压盖等是否在运输和存放过程中产生松动，如发现应均匀拧紧。

Process models of product design were established according to correlation matrix.

所提出的方法在32腔热流道产品设计中得到了应用验证。

In some oil cells,the cupule can be observed,but the occurance of lysis cavaties from oil cells reported by the other authors is not found.

在部分细胞中，可观察到杯形构造，但没有发现溶生油细胞腔的结构。

The Control System for Sealed-off and all-metal RF-excited CO_2 Lasers;2. An experimental study of 100W radio excited diffusively cooled all-metal rectangle waveguide CO_2 laser was carried out.

对新型百瓦级射频激励扩散型冷却全金属矩形波导CO2激光器进行了实验研究，实验中采用了CASE-I平行平面腔，试验结果表明，在采用10%透过率的输出镜时，激光输出最大功率达到146 W，电光转换效率达到17。

The result makes clear, add ply of hempen fiber layer, unit weight, hind back cavity dimension, all can raise hempen fiber to be in medium, low frequency paragraph sound power absorption coefficient.

结果表明，增加大麻纤维层厚度、容重、后背空腔尺寸，均可提高大麻纤维在中、低频段的吸声系数。

In conventional conditions, the lowest temperature for SiGe growth is about 550℃.

在双腔超高真空化学气相淀积生长中，通常采用液氮冷却的方法。

After that , simulated the Die Casting filling process of liquid metal .First use the spical soft Pro/E to construct the model of Die Casting part; Input it to another soft I-deas to form mesh and put the mesh document to the special soft ProCAST.

接着模拟了金属液在模具型腔的充填过程：运用Pro/E软件对泵盖进行三维实体造型，然后把图形导入软件I-deas中进行网格化处理，并将网格化后的模型输入到ProCAST软件中进行了关于压铸工艺参数的多组正交试验的流场，温度场的偶合模拟，进而从多组试验参数中找出最优的压铸工艺参数。

Methods:The MSCT datas of 65 mechanical intestinal obstructions confirmed by operation and pathology were collected and reconstructed with multiplanar reconstruction technique,including 43 cases underwent plain scan;the remaining 22 cases underwent plain and contrast-enhanced scan.Results: Contrast to operation and pathology,there were 25 adhesions,24 neoplasms,5 bowel torsions,5 bezoarhs,4 intussusceptions,2 Crohn's diseases in 65 mechanical intestinal obstructions,the diagnostic accuracy of MPR in mechanical intestinal obstruction was 100%,and the accuracy of the pathogeny was 84.6%.

以往在肠梗阻的诊断中应用最多的为腹部X线平片，但因其信息量不足，对大部分病人不能提出肯定诊断，且对梗阻的病因及病变肠管的血供都无法判断。16层螺旋CT在肠梗阻的诊断中具有明显优势，快速、薄层扫描可得到高质量的各向同性后处理重建图像，在显示肠壁、肠腔和周围结构等方面具有较大优势，有利于肠梗阻的梗阻部位及病因、并发症的诊断。

The results show that the increasing weight of tungsten oxide nanopowders and the color of tungsten nanomaterials turns light yellow from dark blue and black by increasing oxygen partial pressure in blown gas; the decreasing weight of tungsten oxide nanopowders and the color of tungsten oxide nanopowders becomes dark blue by the plasma that compares row increase including the hydrogen.The tungsten oxide nanomrods was increasing with chamber pressures. Urged nanoparticles to have the clavate fusion phenomenon in the development process with increasing plasma currents, and increased the nanorods distribution quantity along with the generated time to be more, 12 minutes later presents all nanorods. This system to prepare a monoclinic crystal W18O49 nanorods successfully, each hourly output approximately is 0.33 gram, and monoclinic crystal WO3 tungsten oxide nanoparticles, each hourly output approximately is 5.77 grams, its growth mechanism is Vapor-Solid solidly the physiognomy explanation.

研究结果显示，随著氧分压增加时，氧化钨材料呈现重量增加趋势，其颜色从黑色至深蓝色转为淡黄色；随著电浆气中含氢气比列的增加，氧化钨材料呈现重量减少，其颜色从淡黄色至深蓝色转为黑色；针对於氧化钨奈米棒而言随了腔体压力增加，奈米棒的数量也会随之增加，而电浆电流的提高，促使奈米颗粒在成长过程中有了棒状熔合现象，且随了生成时间的增加奈米棒分布数量越多，直到12分钟后呈现出多是奈米棒；本制程在适当制程条件下成功制备出单斜晶体W18O49奈米棒，每小时产量约为0.33 公克，与单斜晶体WO3氧化钨奈米颗粒，每小时产量约为5.77公克，其成长机制可透过气-固（Vapor-Solid， VS）相法解释。

At last, in Ansys 9.0 software, by Boolean operation, different parts of the crown （ enamel, dentin and pulp cavity） were separated, and the 3D meshes were created respectively.

再将模型导入Geomagic7软件中进行精修和细化，形成有限元分析软件可识别的实体三维模型，最后，将牙体组织的三维实体模型在Ansys9.0软件中进行布尔运算，区分出釉质、牙本质及髓腔系统，并分别进行了网格划分。

She gently rebuff ed him, but agreed that they could be friends

她婉言拒绝了，但同意作为朋友相处。

If in the penal farm, you were sure to be criticized.

要是在劳改农场，你等着挨绳子吧！