在尺寸上

The relationship of pressure and diameter of tubelike tension bandage is studied and defined through a great deal of test and statistic analysis.

研究圆筒形压力绷带压强与筒径关系，通过大量的测试与数理统计分析，确定二者的数学关系，并在给定的压强与腿部尺寸的基础上，计算得出圆筒绷带编织尺寸，以满足压强要求

It indicates that calculational key lies in correct ascertaining of close loop.

工艺尺寸的计算是在建立尺寸链的基础上进行的。

On the basis of developing a new technology to synthesize sodium diacetate successfully without any pollution,the culture of bigger crystal in perfect shape and single crystal of small dimension suitable for X-ray diffraction was attained.

在研究成功双乙酸钠零污染合成工艺的基础上，培养成功了晶型完美的大尺寸晶体和适宜进行X光结构分析的小尺寸单晶，并进一步应用四圆衍射仪测得其晶体结构。

Measurement discrepancy found at waist,seat,knee,outseam/inseam!

在腰头，坐围，膝围，外长/内长的尺寸与尺码表上的尺寸明显差异

When the undrawn films were annealed atthose temperatures, the morphologies in the lamellar crystals had change. WAXDand iR studies shown that the crystallinities incrcand, dimensions in (002) and(020) normals increased while that in (200) fold had slight decreases. The rela-tionship between the orientation of the drawn UHMWPE gel-films and the struc-ture changes and the optimum drawing temperature had been disscussed.

通过IR及X－ray衍射等方法研究发现，拉伸前用不同温度退火处理后，凝胶膜的片晶微结构产生明显变化，在对应于超高拉伸温度范围内，其结晶度增加，微晶的c和b轴方向尺寸变大，而a轴方向的尺寸减小，从理论上对这一变化过程作了考察，并讨论了超高拉伸取向性与这些结构变化的关系以及可超拉伸取向性的最佳温度范围。

Fixed on the obtruding technics scheme, and made the 3D design of the pressing dies by the advanced CAD/CAE/CAM software --Pro/Engineer(in model Part、Assembly、Manufacturing and Drawing) emphatically, by getting across the analysis of the partˊs structure and combining the punch knowledge.

该零件的尺寸是通过测量得到的，在零件图上未注明尺寸公差，精度要求不高。材料为08钢，料厚为0.9mm。结合以前所学过的模具知识，运用Pro/Engineer做冷冲压模具三维设计。

In order to determine further the profile of scrolls,the structural characteristics of superchargers with double-sided scrolls were analyzed and the principle of determining initial involute angle s was presented on the conditions of definite initial involute angle s,radius of base circle,and depth of scrolls.

在渐开线起始角、基圆半径和涡旋齿深度确定的条件下，为进一步确定涡旋齿的齿形，对双侧涡旋增压器的结构特征进行分析，提出始端渐开角的确定原则。通过吸气腔和排气腔的容积计算，结合回转角与渐开角的关系，给出涡旋齿始端和终端渐开角的计算方法。结果表明：该计算方法能较准确地确定涡旋盘的结构尺寸，从而可估算出整个压气机的尺寸是否满足汽车上有限的安装空间

Packing ring preparations 1 braided At the appropriate size of the axis of winding packing or packing ring using calibrated cutting machine; upon request, packing neatly cut into the butt, or miter (30-45 degrees), a cut of a ring, and use shaft or stem test size is appropriate.

编织盘根在适当尺寸的轴上缠绕盘根，或使用校准过的盘根环切割机；根据要求干净利落地切割盘根成对接或斜接（30-45度），一次切一个环，并用轴或阀杆检验尺寸是否合适。

Based on the dimension chain we draw, we analyzed the motions andforces of the system.

然后在绘出尺寸链的基础上，对结构进行运动与力分析，最后对零部件的具体尺寸进行设计与校核。

Based on the characteristics of parameterized design and key technologies of knowledge based engineering, and specially according to the characteristics of the construction, figure, assembly-parameter of bicycle frame design, the article has achieved repeated using of experiential parameter and knowledge by adopting methods such as automatic reading experiential datasheet, computing parameter by making use of program, manual data-input or modifying and so on. Based on analyzing the characteristics of Rear End design and the associated characteristics with Chain Stay and Seat Stay, different design methods are analyzed in detail, and rapidly assembling of Rear End, Chain Stay and Seat Stay is achieved by using the method of combining top-down-assembly with down-top-assembly method. Based on analyzing special technologies and UDF characteristics, the repeated using of different sectional shapes by using UDF technology on the tube section design is also achieved, and this will greatly shorten the time spent on fixing the dimensions and orientations on sketches.

在探讨了参数化设计技术特点和知识工程关键技术的基础上，针对自行车车架设计中的结构、形状、装配参数特点，分别采用了读入经验数据表、参数程序求解、手工录入或修改方法实现车架设计经验参数和知识的重复利用；在分析自行车后叉片设计特点及与平、立叉的关联特性的基础上，对不同的设计方案进行了详细分析，并采用自顶向下和自底向上相结合的方法，实现了后叉片的快速装配定位与平、立叉设计相关联；在分析了特征技术和UDF特点的基础上，将UDF用于管件截面的设计上，使各种截面形状能不断重复利用，大大节省了约束草图尺寸和位置的时间。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了