在...的中途

Ovary 2-locular, carpels free at apex; ovules mostly 1 per carpel, less often many, but then most of them sterile, crassinucellar, bitegmic, anatropous, halfway between apotropous and epitropous, pendent from ovary top if solitary, along the carpellary margins if numerous; placentation axile.

子房2室，心皮离生在先端；每心皮多数的胚珠1，较少的通常很多，中途在apotropous和胚珠向上转之间，然而他们中大多数不育，crassinucellar，bitegmic，倒生，中轴胎座花柱和柱头2。

Many people are internally and externally in the pursuit of self-confidence and calm, standing on the same starting line, but always in the middle is divided into two very different: the former suffers from the test of time, become peaceful, calm, flying every day live as if life listened attentively, the latter can not afford its time of invasion, trivial, yung lazy, mediocre, in the plain spend time under the cover of Time.

许多人都在追求内外兼修的自信与从容，站在同一起跑线上，却总会在中途分成截然不同的两者：前者经受着时光的考验，变得祥和、平静、飞扬，每天都在用心生活用心聆听，后者却难以承受时光的侵袭，琐碎、庸惰、碌碌，在平淡的时光遮掩下消磨时日。

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

Business card printing and membership card when making half-way down, rollers and ink roller will not dry crust.

制卡和会员卡制作中途停机时，在墨辊和网纹辊上的油墨也不会干燥结皮。

Maybe somebody you met when you were both stuck in the airport on unexpected layovers emailed you to let you know they finally reached their destination -- but they're itching to meet up with you again.

又或许是当飞机中途停留时你在候机厅遇到的某人发邮件告诉你他已经到达目的地，但是多么渴望与你再次相会。

They tried this first from partway up the slope where the rover had spent the winter.

他们第一次尝试是在勇气号过冬时所在的斜坡中途。

Datagrams also allow the routers to balance the traffic throughout the subnet, since routes can be changed partway

资料封包也允许路由器去协调贯穿子网路的运输，因为路径能够在中途改变

It is true that the programme has managed to hit two out of the five missiles fired over the past five years during tests of its main component, the ground-based midcourse missile defence system.

这是事实，该方案已设法击中两列的五枚导弹发射在过去五年期间，测试，其主要组成部分，地面陆基中途导弹防御系统系统。

Adrift in the middle of the Indian Ocean, the Cocos Keeling Islands lie halfway between Australia and Sri Lanka.

Cocos Keeling群岛位於澳洲与斯里兰卡中途，浮沉在印度洋的中央。

Real estate in 2003 the new decade,"Midway"

房地产在2003年新的十年，&中途岛&

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。