圆筒

Of, relating to, or having the shape of a cylinder, especially of a circular cylinder .

圆柱形的，圆筒状的圆筒状的，与圆柱形有关的，或具有圆柱体形状的，特别是圆形的柱体

"Cylindric:Of, relating to, or having the shape of a cylinder , especially of a circular cylinder ."

"圆柱形的，圆筒状的：圆筒状的，与圆柱形有关的，或具有圆柱体形状的，特别是圆形的柱体。"

Blanket cylinder: In an offset printing press, the cylinder around which the blanket is clamped.

胶布圆筒：柯式印刷机上被胶布环绕而夹紧的圆筒。

Common impression cylinder press: A design of offset printing presses using a common imoression cylinder for two -colour and four-colour machines.

公用压力圆筒印刷机：柯式印刷机的一种设计。变色机和四色机都共同使用一个别压力圆筒。

Aiming at reducing cogging force in tubular permanent magnet linear motors, an analytical method based on energy method and Fourier series expansion was adopted, the expression of cogging force was deduced which is related with structure parameters of the motor.

为削弱圆筒永磁直线电机的齿槽力，采用了一种基于能量法和傅里叶分解的解析分析方法，推导出了圆筒直线电机与结构参数有关的齿槽力表达式。

Several affect factors of cylinder part limiting drawing parameter in deep-drawing were summarized in detail. Some new and practically applicable equations for estimating the limiting drawing parameter in the cup-drawing of a cylindrical cup with a flat-nosed punch are derived separately based on the load-maximum principle for localization of the plastic flow.

目前，国内外对极限拉深系数进行的研究较多，文献中详细地总结了板料成形中圆筒件极限拉深系数的若干影响因素，并基于最大承载原则提出了一些计算圆筒件极限拉深系数的实用公式。

One or more plane sections (8,9) and part cylinders (10,11) connecting to the plane sections (8,9) are formed at the outside (7) of the capillary using for fixing the fiber, all the part cylinders (10,11) are formed with a single center axis and the same radius, meanwhile a patchhole (3) of the inserting fixed fiber (2) is formed in the deflected position of the center axis and in the vertical direction of the first plane section (8) which is used as the standard.

在光纤固定用玻璃毛细管(1)的外面(7)形成有一个或多个平面部(8、9)和与该平面部(8、9)连接的一个或多个局部圆筒面(10、11)，该所有的局部圆筒面(10、11)都是以单一的中心轴和相同半径形成的，同时在与作为基准的第一平面部(8)垂直的方向上从中心轴偏离的位置上形成有插入固定光纤(2)的插入孔(3)。

The pressure hull is an important element of submarine structure which can withstand the external pressure, the pressure hull is composed of cylinder and dome for the most part, and needs to weld stiffeners on the cylinder within a moderate space.

潜艇在水中主要由压力壳来承受水压，而小型潜艇之压力壳大都由圆筒壳及半球型壳组合而成，并在圆筒壳上之适当距离焊接环状肋骨作为补强。

Research on the factors affecting impact force of thin-walled tube s;2. The tangential residual stress of the external surface of the autofrettage tube s was measured by X rays.

对自增强圆筒进行X射线外表面切向残余应力测量，在模型考虑材料反向屈服后的强化现象和鲍辛格效应影响的基础上，给出了自紧圆筒强度的计算方法。

Cm; sepals connate beyond attachment to ovary, abaxially glabrous; tube subcylindric, 1-1.5 × 0.8-1 cm, not constricted at throat, adaxially tessellate, orifice ring less than 1 mm wide; lobes broadly ovate, 0.5-0.7 × 0.5-0.7 cm, base smooth.

花序梗上升，花萼深紫色，圆筒状到钟状，1.5-2.5 1-2 厘米*约1厘米萼片合生超过贴生的子房，背面无毛；筒部近圆筒状， 1-1.5 * 0.8-1 厘米，并非缢缩的在喉部，正面棋盘格状，开口环不到1毫米宽；裂片宽卵形， 0.5-0.7 * 0.5-0.7 厘米，基部平滑。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。