圆盘

With the wide usage of the lamped circular saw and the high price of materials in wood industry, the kerf loss gets more attention, because it can decease the production and increase the cost.

随着夹盘圆锯片在生产实践中得到广泛地应用以及原材料成本的提高，锯片本身的厚度和横向振动所带来的锯路损失引起了更多的关注，锯路损失降低了出材率，加大了生产的成本。

Farmer used the term gem for her corn recipe, which was a muffin baked in a pan of lozenge shapes rather than circular cups.

Farmer在她的用玉米作muffin的食谱中使用了一个词"珍宝"，这种方法要将muffin在一个菱形而非圆杯形的盘里烘烤。

This paper presents a new method to determine the minimum basic circle radius of a plate cam with a roller follower by the allowable pressure angle, and gives the feasible region of geometrical parameters of the cam mechanism.

介绍按许用压力角确定滚子从动件盘形凸轮最小基圆半径的一种新的解析方法。同时给出凸轮机构几何参数的可行域

A moon hung above the water like a silver plate.

一轮圆月就像银盘一样悬挂在水面上。

From an open box on the majolicatopped table he extracted a black diminutive cone, one inch in height, placed it on its circular base on a small tin plate, placed his candlestick on the right corner of the mantelpiece, produced from his waistcoat a folded page of prospectus entitled Agendath Netaim, unfolded the same, examined it superficially, rolled it into a thin cylinder, ignited it in the candleflame, applied it when ignited to the apex of the cone till the latter reached the stage of rutilance, placed the cylinder in the basin of the candlestick disposing its unconsumed part in such a manner as to facilitate total combustion.

422他从马略尔卡瓷面桌子上的一个敞着的盒子里取出个一英寸高、又小又黑的松果，将其圆底儿放在小小的锡盘上。然后把他的烛台摆在壁炉台右角上，从背心里掏出一张卷起来的简介，题名"阿根达斯。内泰穆"。打开来，大致浏览了一下，又将它卷成细长的圆筒，在烛火上引燃了。于是，圆筒的火苗伸到松果尖端，直到后者发出红色火光；并将纸筒撂在烛台托子上，让剩下的那部分燃烧殆尽。

While the most dismally traditional astrologers referred to these angular relationships as "malefic" or "evil" due to the dynamic and challenging quality of the interaction between the 2 planets involved, the Hamburg School astrologers and the later Cosmobiologists and Uranian astrologers have continually verified that these are the most energetic angular relationships and therefore of greater significance for personal growth, and for prognosis of significant change and developmental periods.

90dial 盘的基本定理不是那么复杂， dial 是基于 4 倍相位的，把 360 度圆分成 4 个相等的部分 360 ÷ 4 = 90 ，根据占星家们几个世纪的经验，对应传统相位的合相 0 度，刑相（ 90 度和 270 度）和冲相 180 度的 4 倍相位，是行星间非常有力的关键相位，由于产生这这个相位的两颗行星互相改变与挑战对方，许多传统的占星学家会认为这个相位是有害的，甚至邪恶的，汉堡占星学家和稍微晚一些的宇宙生物学家经过长期的经验，认为 90 度相位是非常有力的基本角状角度，所以对个人成长非常有利，对日后的改变与发展非常有利。

Style straight or declinate to deflexed, persistent; stigma capitate-discoid, crenate to lobed.

对外折，宿存下倾的花柱直或；盘状柱头头状，具圆齿到浅裂。

During the CTP process, the wafer or polishing pad is fixed and another component is translationally moving along a circular track with constant velocity.

圆平动研抛是工件或研抛盘之一固定不动，而另一构件以恒定的速率沿圆形轨迹做平动而实现的抛光过程。

In order to determine further the profile of scrolls,the structural characteristics of superchargers with double-sided scrolls were analyzed and the principle of determining initial involute angle s was presented on the conditions of definite initial involute angle s,radius of base circle,and depth of scrolls.

在渐开线起始角、基圆半径和涡旋齿深度确定的条件下，为进一步确定涡旋齿的齿形，对双侧涡旋增压器的结构特征进行分析，提出始端渐开角的确定原则。通过吸气腔和排气腔的容积计算，结合回转角与渐开角的关系，给出涡旋齿始端和终端渐开角的计算方法。结果表明：该计算方法能较准确地确定涡旋盘的结构尺寸，从而可估算出整个压气机的尺寸是否满足汽车上有限的安装空间

After analyseing the force of all the component in the cam with Direct-Moving-roller follower, the conclusion is gained that radius of base circle not only influence the ability of sending force, but also influence the roller s continuous rolling .

对滚子直动从动件盘形凸轮机构各构件进行了受力分析后，得出基圆半径的大小不仅影响传力特性，还影响滚子是否能做连续滚动的结论。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。