圆的直径

The spiral angle of graduated circle was rough estimated by measuring the addendum circle diameter and modified on milling machine.

介绍了精确测绘单一斜齿圆柱齿轮齿形参数的简便方法，即测量公法线长度计算基圆齿距从而查表确定模数和压力角；测量齿顶圆直径估算分度圆螺旋角，用分度头在铣床上修正分度圆螺旋角，并进行误差分析。

Pitch circle diameter: d = mz = 3X12 = 36 Tooth crown heights: ha = m (f0 + x)= 3X (l +0.5)= 4.5 Tooth High: hf = m (f0 + cx)= 3X (l +0.25-0.5)= 2.25 Tooth full height: h = ha + hf = 4.5 +2.25 = 6.75 Addendum circle Chemical pumps diameter: Da = d +2 ha = 36 +2 X4.5 = 45 Fixed string tooth thickness: Sxn = m (π/ 2 * cos2a + xsin2a)= 3X (1.387 +0.6428 X0.5)= 5.125 Fixed string of high gear tooth thickness measurement: hxn = m (π/ 8 * sin2a + xsin2a)= 3X (0.7476X0.117X0.5)= 2.42 Modulus coefficient x0.5 m3 O20 ° pressure angle tooth thickness Sxn5.12 fixed string Addendum Coefficient string f1 fixed gear tooth thickness measurement most high hxn2.42 Teeth z12 2, shaft wear and tear maintenance: Axis gear pump wear is mainly because with the support roller shaft at both ends between the friction and wear, so that smaller shaft diameter.

分度圆直径：d=mz=3X12=36 齿顶高：ha=m（f0+x）=3X（l+0.5）=4.5 齿根高：hf=m（f0+c-x）=3X（l+0.25-0.5）=2.25 齿全高：h=ha+hf=4.5+2.25=6.75 齿顶圆直径：Da=d+2ha=36+2X4.5=45 固定弦齿厚：Sxn=m（π/2*cos2a+xsin2a）=3X（1.387+0.6428X0.5）=5.125 固定弦齿厚测量用齿高：hxn=m（π/8*sin2a+xsin2a）=3X（0.7476X0.117X0.5）=2.42 模数m3变位系数x0.5 齿形角o20°固定弦齿厚Sxn5.12 齿顶高系数f1固定弦齿厚测最齿高hxn2.42 齿数z12 2、轴的磨损维修：齿轮泵中轴的磨损主要是因为轴两端与支撑滚针间的摩擦磨损，使轴径变小。

The class one which was expressed by diameters of pore maximum inscribed circle was adapted and a new distribution model expressed by diameters of pore area equivalent circle modified with fiber thickness was presented.

以几何概率和平面随机分割理论为依据，分析了非织造布中孔隙结构的分布模型，将经典的以内按圆直径表示的有效孔径分布模型改为以面积等效圆直径表示的有效孔径分布模型，并结合纤维细度进行修正，实验证明，该模型更符合实际情况。

As the number of impressions increase, however,the pitch circle diameter design becomes progressively more impracticable as the runner length, which is a function of the pitch circle diameter, is also increased.

可是随着型腔数目的增加，由于流道长度是等分圆直径的函数，所以设计的流道长度随着等分圆直径的增加变得不现实。

And the polar angle and the polar radius was represented into AutoCAD polar coordinate, the involute was drawn through the spline linear tool. And then, a section of the involute was intercepted with the diameters of the point circle and the root circle, used it as the tooth face of the spline. The involute tooth thickness was drawn using the diameter of the divided circle and the tooth-form was drawn through rotating, mirroring image and cutting.

根据DIN 3960渐开线花键的坐标值，用EXCEL函数功能计算出不同压力角下渐开线的极角和极半径，表示成AutoCAD极坐标并通过样条线工具绘制出渐开线，再用齿顶圆和齿根圆直径截取一段渐开线作为为花键齿面，并用分度圆直径绘制出渐开线齿剖面，经镜像和裁剪便可绘制出渐开线齿形。

The welding distortions of the diaphragm with coroneted blades in steam turbine have been studied with model and production experiments in this thesis. It is a main purpose to find out the rule of welding distortion of the diaphragm in radial, circumferential and axal direction.

为了掌握蒸汽轮机自带冠靜叶隔板焊接产生的直径变形、半径变形、节圆收缩率和倾斜变形的基本规律、提出减小和调整焊接变形的合理工艺措施，本文通过基于正交设计的模型试验和现场监测对自带冠靜叶隔板的焊接变形进行了研究。

Elaborated the punching components formation principle, the basic dies structure and the rate process and the principle of design; and designed some conventional punching die:the die for big diameter three direction pipe which solved the problom of traditional machining,the drawing and punching compound die with float punch-matrix,代写医学论文,the drawing and cutting compound dies with unaltered press,the compound die for the back bowl of the noise keeper,the design of the compound die which could produce two workpieces in one punching,the bending die for the ring shape part ,the bending die which used the gemel ,automate loading die for cutting, the drawing,punching and burring compound dies with sliding automated loading,the punching die for the long pipe with two row of hole,the drawing die for the square box shape workpiece and the burring die for the box shape workpiece.

本文对冷冲压技术的分类、特点及发展标的目的作了简略概说；论述了冲压零件的形成原理、基本模具结构与运动过程及其设计原理；对典型的冲压件模具举行了设计：大直径三通管冲压复合模设计盖世了大直径三通管的加工困难的问题、带有浮动凸凹模的拉伸冲孔复合模设计、适力压边式落料拉伸切边复合模设计、消音器后补碗落料、拉深、冲孔、翻边复合模设计、一模两件落料拉伸冲孔翻边复合模设计、圆环弯曲件的模具设计、铰链卷圆成形工艺及模具设计、半自动送料切角装配设计、滑板式送料拉深、冲孔、翻边模设计实现自动送料、长管多孔冲模设计、带凸缘台阶方盒形零件拉深模和盒形件侧壁小孔翻孔模。

Elaborated the punching components formation principle, the basic dies structure and the rate process and the principle of design; and designed some conventional punching die:the die for big diameter three direction pipe which solved the problom of traditional machining,the drawing and punching compound die with float punch-matrix,代写医学论文,the drawing and cutting compound dies with unaltered press,the compound die for the back bowl of the noise keeper,the design of the compound die which could produce two workpieces in one punching,the bending die for the ring shape part ,the bending die which used the gemel ,automate loading die for cutting, the drawing,punching and burring compound dies with sliding automated loading,the punching die for the long pipe with two row of hole,the drawing die for the square box shape workpiece and the burring die for the box shape workpiece.

本文对于冷冲压技术的分类、特点及成长方向作了简略概说；论述了冲压零件的形成原理、基本模具结构与运动过程及其预设原理；对于典型的冲压件模具进行了预设：大直径三通管冲压复合模预设盖世了大直径三通管的加工难题、带有浮动凸凹模的拉伸冲孔复合模预设、适力压边式落料拉伸切边复合模预设、消音器后补碗落料、拉深、冲孔、翻边复合模预设、一模两件落料拉伸冲孔翻边复合模预设、圆环弯曲件的模具预设、铰链卷圆成形工艺及模具预设、半自动送料切角装置预设、滑板式送料拉深、冲孔、翻边模预设实现自动送料、长管多孔冲模预设、带凸缘台阶方盒形零件拉深模和盒形件侧壁小孔翻孔模。

Screws, bolts, or nuts without washers must be loaded against a test plate with a minimum diameter clearance hole equal to the nominal thread size plus 0.50mm for fasteners M6 (1/4 inch) and smaller, and plus 1.0mm for larger diameters.

无垫圈的螺钉、螺栓、或螺母应被装夹到具有较小孔径的通孔的试验圆板上进行试验，对于≤M6 (1/4 inch)的紧固件，试验圆板的孔径为公称螺纹直径加上0.50mm，对于＞M6 (1/4 inch)的紧固件，试验圆板的孔径为公称螺纹直径加上1.0mm 。

The round moon cakes, measuring about three inches in diameter and one and a half inches in thickness, resembled Western fruitcakes in taste and consistency.

圆的中秋月饼，测量直径和一的大约三寸而且测量厚度的一半的寸，相似了味道和一致性的西方掺有干果的糕饼。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。