圆柱体

After optimizing the technological technique, the parameters on microwave magnetic sintering of NdFeB magnets were chosen: the powder with average particle size of 3μm was isostatically pressed at 2000kg/C㎡, and the shape of the green compact is φ18×6mm.

进行工艺优化后，我们所选用的微波烧结参数为：微波功率2kW，粉体的平均粒径3μm，压型压力2t/cm2，初坯为φ18×6mm的圆柱体，烧结最高温度约为900℃，烧结的时间70s左右。

The thesis suggests an algebraic grid generation method for calculating the transient flow problem of a small rigid circular cylinder oscillating rectilinearly inside a large circular fluid tank.

中文摘要本文旨在建议一个代数格网生成方法，以计算圆柱体於大型圆形液槽内水平振动之流场。

Right-click the cylinder, go to Properties and de-select Renderable.

右击圆柱体，进入属性框，关闭可渲染属性和Backface Cull。

It was discovered that tensile strength regularity varied with carbonated zone and half- carbonated zone and uncarbonated zone of the hydraulic carbonated concrete.3 Rusty fundamental of rebar is explained; Rusty rebar of the long-age hydraulic reinforced concrete that corrosion ratio is less than 6 percent is been mechanical test.

采用圆柱体横劈法测定了长龄期水工碳化混凝土的三个分区强度，揭示了此类水工混凝土碳化区、反应区和未碳化区的强度变化规律。

These oversized furry cats, with a masterful sense of smell and long bushy tails, then digest the cherries for up to 72 hours before defecating them out in fir-conesque cylinders.

这些嗅觉灵敏、浓毛长尾的特大号猫，消化浆果的时间最长要达到72小时，然后将其排进冷杉球果状的圆柱体里面。

Same thing I did for the second part of it and I also created a cylinder and extruded parts of it to create antenna.

同样的事情我没有为它的第二部分，我也创建了一个圆柱体和它的冲压件制造天线。

Sharp, spicy blue with wonderful creamy texture. Some of finest Italian Gorgonzolas still aged in caves. Cylinders varying in size from 13 to 29 pounds. Thick, coarse reddish-gray rind with powdery patches. Pale cream with greenish-blue veined paste."Dolce" version very creamy, more perishable and less piquant.

味道强烈、辛辣的蓝霉奶酪，有着很好的乳脂质地；一些最好的意大利Gorgonzolas干酪仍然在山洞里成熟；13至29磅的圆柱体；厚的、粗糙的，微红灰色外壳带有粉状斑点；苍白色的奶酪带有绿相蓝色条纹；&Dolce&版本的奶酪非常乳脂化，更易腐坏，也更少辛辣。

They were prisoned in a cylinder near a damp dam ,they had to sit on the cushions and studied curriculum .they kept damning the correspondence.they deemed that they will dedicat the rest of their life there even the state was in a deficit .

他们被监禁在一个潮湿大坝的一个圆柱体里。在那里他们不得不坐着垫子上，学习全部的课程。他们不挺的咒骂那个通信员。他们深信，虽然这个国家面临财政赤字，他们将在这里度过余生。

Where his right hand should have been, a capped cylinder of black leather protruded from his sleeve.

原该是他右手的地方，从袖子里伸出的是黑色皮革的圆柱体。

3D-CTM (Coupled Thermo-Mechanical Forming Simulation) software for precision forging process of aero-engine blade was developed. The key technologies of 3D coupled rigid-viscoplastic thermo-mechanical FEM simulation of blade forging process were studied systematically. By using the remeshing method of contracting from the boundary to the inner, new mesh system from old distorted mesh system can be obtained. A method of modifying the position of nodes touching on the die according to its original normal was proposed to avoid "dead lock" problem due to uncontinuity of normal of scatted die meshes. The pseudo-static iterative algorithm was used to simplify the coupled thermo-mechanical computation. In particular, formulations to determine relaxation factor β was established for rigid viscoplastic FEM adopting penalty function method, and an improved cubic factor rapid algorithm derived from these formulations was proposed by combining with the advantage of advance and retreat search method.

采用基于边界构形的内缩法，实现了三维畸变网格的重新划分；提出了初矢修正法对触模节点的位置进行修正，解决了由于离散的模具网格的法矢不连续造成的&死锁&问题；采用准静态迭代法简化了速度场和温度场耦合计算过程；特别是针对减速因子β的选取，建立了适用于三维复杂成形过程刚粘塑性罚函数法有限元三次因子法的计算公式，并结合进退搜索法提出了改进的三次因子快速算法，提高了模拟计算效率和稳定性，在此基础之上，开发了面向叶片精锻过程的三维刚粘塑性热力耦合有限元模拟分析系统(3D-CTM)，系统的可靠性得到了圆柱体镦粗的验证。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了