圆和

For direct injection DESMA offers rotary tables with 6, 12, 18, 24 and 30 stations and for unit sole machines 6, 12, 18, 24, 30, 42, 60 and 80 stations.

在连帮注射方面德士马提供的圆盘机有6，12，18，24和30工位的选择，而在鞋底机方面则有6，12，18，24，30，42，60和工位的选择。

Firstly, a quantitative relation about finite deformation and geometrical parameters which exhibit variation of laser spectral image was introduced. And then, particular emphasis was put on some important computer processing steps related to the analysis of spectral image, such as digitizing, segmentation, feature extraction and analytical algorithms. Lastly, some examples about an experiment of a ring subject to large diametral compression were given.

文中首先给出了有限应变和平均整旋角与反映频谱图像变化的几何参数之间的定量关系，然后着重介绍了与频谱图像分析有关的数字化、分割、特征提取和分析算法等重要的图像处理过程，最后给出圆环受径向荷载大变形实验的分析实例。

Furthermore, the interaction of L-C10HL and D-C10HL with cyclodextrin was also investigated by fluorescence excitation spectrum and circular dichroism spectrum.

利用荧光激发光谱和圆二色性谱研究了L-C10HL和D-C10HL与环糊精之间的相互作用。

Oxygen/ fuel torch sets, propane torches, electric welders, portable disk or wheel grinders, portable lead pots and tar buckets are some examples of such tools and equipment.

氧气/燃料焊枪、烷气割炬、焊工、提圆盘或车轮磨工、提铅罐和沥青桶都是类似的工具和装备的例子。

In strictly, it is hard to make the light normal incident into the sphere, double refraction will take place in crystal sphere when a TEM〓 mode Gaussian beam oblique incident into the sphere, and the two orthogonal polarized beams are both elliptical Gaussian beam. The ellipticity and eccentricity of the elliptical Gaussian beam will change with the incident angle, and for a fixed incident angle, they will change with the shifting of incident beam waist position.

由于严格意义上的正入射较难实现，基模圆高斯光束斜入射晶体球后将在球内产生双折射，且球内偏振态正交的两束折射光都将是椭圆高斯光束，它们的椭圆度e和偏心度Δ随入射角的改变而改变，在入射角一定的情况下，入射光束束腰的移动也将改变这两束折射光的椭圆度e和偏心度Δ。

The main products are:"30 mm, 26 mm-mm, 24 mm and 20 mm hammer; 13 mm, 10 mm, and 6 mm electric drill and impact drill; 110 millimeters marble cutter, 100 ~ 150 mm series of angular grinding ray machine, electric saw, sanding machine."

主要产品有："30毫米、26毫米毫米、24毫米、和20毫米电锤；13毫米、10毫米、和6毫米电钻及冲击钻；110毫米云石切割机、100~150毫米系列角向磨光机、电圆锯、砂光机等。"

The products of steel and pipe including: welded steel pipe、square and rectangle pipe、electroplate steel strip.

钢和管类产品包括：焊接钢圆管、正方形和长方形管、电镀钢条等。

Within the 14th time window, all the three tides are generally elliptically rather than circularly or linearly polarized. However, both △(subscript φ24) and △(subscript φ12) in this window are quasi-quadrature at all heights while △(subscript φ8) are quasi-in-phase at 92.0 and 94.0 km.

在第14个时间窗内，三个潮汐一般表现为椭圆振而不是圆偏振或线偏振，但是△(下标φ24)和△(下标φ12)在三个连续的高度上准正交，而△(下标φ8)在92.0和94.0 km上准同相。

Abstracts: MMB1320B-type cylindrical grinder applies hydraulic pressure Systematic and electricity-control-mode drive to realize the motion of the working table and emery wheel rack.. This article improves the method of electricity control and uses PLC soft ware instead of a large amount of centre relay and time relay of relay control system to realize the control of hydraulic pressure so that we can save energy and enhance efficiency.

摘 要： MMB1320B 型外圆磨床采用液压系统和电气控制方式驱动以实现工作台和砂轮架的动作，本文对其电气控制方式加以改造，用 PLC 软件取代继电器控制系统中大量的中间继电器、时间继电器等以实现液压系统的 PLC 控制，从而达到节能增效的目的。

With the theory, any straight lines and quadratic curve′s equidistance curve can be indirectly interpolated with the help of outline and wire circle′s information, it is unnecessary to calculate equidistance curve .

该理论直接利用轮廓曲线和丝圆的信息，不需计算等距曲线，间接实现任意直线和二次曲线的等距曲线的插补，有效地避免了传统计算等距曲线产生的计算误差，简化了数控机床控制程序设计，提高了机床的控制精度。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。