固有

In chapter three, the new concepts of the bifurcation point and asymptotic bifurcation point of compact continuous operators in Menger PN-spaces are introduced. Some sufficient conditions for the existence of the bifurcation point and asymptotic bifurcation point are obtained. And the problems on the intrinsic value and intrinsic element of compact continuous operators are studied in Menger PN-spaces. A series of theorems on the existence of the intrinsic value and intrinsic element are obtained.

第三章，在概率赋范线性空间中提出非线性算子的歧点和渐近歧点的新概念，获得了非线性算子存在歧点和渐近歧点的充分条件；讨论了Menger概率赋范线性空间中非线性算子的固有值和固有元问题，得到了非线性算子存在固有值和固有元的一系列充分条件。

Note that such a W must involve either a different corpus of intrinsic properties from those in our world, or no intrinsic properties at all. A type-F monist who holds that the only coherent intrinsic properties are protophenomenal properties might end up denying the conceivability of zombies, even under a structural-functional description of their physical state – for reasons very different from those of the type-A materialist.

主义这样的W必须含有，或者和我们这个世界不同的固有属性，或者没有固有属性。F类一元论认为仅由的融贯的固有属性是主现象属性，可以中止于对人偶设想的拒绝，即使在一个结构功能描述的物理事态下，理由不同于A类物质主义者。

The effect of tribology factors on bearing vibration is studied experimentally. AR model and WPT are used to processing the normal arid abnormal signals. The results are as follows:1. The vibration of ball bearings is caused by the tribology action of contact pairs of ball and ring races and has the essential of tribo-dynamics. Any factors affecting the tribology characteristics of contact pairs will affect vibration and noise of bearings consequently.2. Vibration characteristics of bearing keep almostly unchanged with the increasing of axial load expecting the increasing of nature frequencies. When radial load increasing with axial load unchanged, nature frequencies keep unchanged but some new vibration peaks appears in the spectrum.3. Vibration amplitudes are damped and nature frequency are enhanced with sufficient lubrication. Vibration and noise of bearings increase obviously and roar can happen and the contact surfaces scratch slightly under insufficient and unclean lubrication state. Bearing will be disabled in a few minutes without any lubrication.4. Bearing vibration is unstable under low speed. With the speed increasing, the vibration become stable and natural frequencies increase slightly but the amplitudes increase apparently.5. Bearing vibration can be excited only by some harmonics ofwaviness without lubrication and by all harmonics with lubrication based on the theoretical analysis.6. The nature frequencies of ball bearings decrease with the increasing sizes. When international clearance increasing, nature frequencies decrease in radial and increase in axial and angular and the amplitudes increase in radial and decrease in axial and angular. When the number of balls increasing, nature frequencies increase and amplitudes decrease. When the pitch diameter increasing, axial nature frequency increase and others nearly keep no change. When outer race groove curvature radius increasing, nature frequencies increase in radial and decrease in axial and angular and amplitudes keep no change in radial and increase in axial and angular. When inner race groove curvature radius increasing, nature frequencies decrease and amplitudes increase.7. The distortion in amplitude and frequency components of bearing vibration signals picked up by the present probe measurement method is founded and right conclusions cannot be achieved by the signals. When accelerometer is rigidly screwed with steel stud onto a flat outer surface of a ball bearing, vibration signal can be got without distortion and the reliability of research on bearing vibration is assured.8. AR model is suitable for large samples of bearing vibration signals, square root of length of samples can be used as the upper limitation of order determination and the FPE order selection criterion is effective. Many advantages of AR spectrum are founded over the classical based on FFT.9. Time-Frequency analysis is necessary for abnormal noise of ball bearings. WPT overcomes the principle shortcomings of STFT and proved to be a best tool to process the abnormal signals.

理论分析和试验研究表明： 1球轴承振动是钢球—滚道接触副中的各种摩擦学作用引起的，具有摩擦动力学的本质，任何对接触副的摩擦学特性有影响的因素都将对球轴承的振动和噪声特性产生影响； 2中心轴向载荷作用下，载荷增大使球轴承的固有振动频率升高，载荷越大同样的载荷增幅引起的频率升幅减小，足够大的中心轴向载荷作用下载荷的变化对球轴承振动的频率特性不会产生明显的影响； 3轴向和径向联合载荷作用下，径向载荷不大时球轴承振动的固有频率基本不变，但是可能引起变刚度激励的非线性振动，出现新的频峰，过大的径向载荷将使部分钢球脱离接触，使球轴承的振动和噪声呈现不稳定状态； 4润滑对球轴承的振动和噪声特性有重要的影响，良好的润滑对振动有明显的抑制作用，润滑不充分时，振动和噪声的水平会有明显增高，一定条件下还会激发接触副中的谐振，发出啸声，造成接触表面的伤害，无润滑干接触时，短时的运转就会损伤接触副表面，使振动和噪声迅速增大，并随时可能引发严重的磨损和卡滞失效；接触副润滑良好时，油膜的"刚化效应"使球轴承振动的固有频率有所提高，润滑剂中含有弥散性污浊时，振动的幅度总体升高，但弥散性污浊不会改变球轴承振动的频率特性；浙江大学博士学位论文：球轴承振动的研究 5低速时，球轴承振动的基本特征呈现不稳定状态，随着转速的提高，球轴承振动的频率特性趋于稳定，固有频率频峰升高； 6理论分析表明，干接触时钢球和滚道表面波纹度的某些谐波分量能激励球轴承的振动，振动的幅值与谐波幅值成正比，实际球轴承中钢球的分布不可能完全均匀，波纹度的激励作用会随时发生；润滑接触的分析表明，波纹度的任意谐波分量均能激励球轴承的振动； 7球轴承的几何和结构参数分析表明，球轴承尺寸越大，径向、轴向和角振动的固有频率越低；钢球中心圆直径增大，球轴承的径向和轴向振动的固有频率基本不变，角振动的固有频率有所上升，振动的幅频特性基本不变；径向游隙加大使球轴承的径向振动固有频率降低，轴向和角振动的固有频率有所升高，径向振动幅频特性的幅值升高，而轴向和角向降低；钢球的数量增多使球轴承振动的固有频率上升，幅频特性的幅值下降，径向振动的幅值下降最为明显；外圈沟曲率半径系数增大使球轴承径向振动的固有频率升高，轴向和角振动的固有频率降低，径向幅频特性基本不变，轴向和角向幅频特性幅值升高；内圈沟曲率半径系数增大使径向、轴向和角振动固有频率均下降，振动幅频特性的幅值均有升高； 8试验对比表明，传感器采用探针式安装时，由于探针接触副接触特性的影响，钡(量得到的球轴承振动信号有失真，采用专门设计和制作的试验球轴承，以固定式安装加速度计，首次测量得到了球轴承振动的真实信号，通过对振动信号的分析，验证了球轴承振动的理论模型； 9)基于时间序列分析的AR模型适用于大样本球轴承振动信号的分析，以样本长度的均方根值作定阶上界，FPE做判阶准则，给出的AR谱光滑，频率分辨率高，是球轴承振动分析的简便而可靠的手段； 10以时频域分析的小波包变换分析球轴承异音信号能够比较好地定位和聚焦异音发生的时间，时间间隔，频率范围，同样是球轴承振动分析的可靠的手段，可用作球轴承故障诊断技术。

It is found that the main source of fillet weld's angle distortion is the inherent shear strain component ε but not the transverse inherent normal component.

结果发现：角焊缝产生角变形的主要根源是固有剪切应变，而不是传统思维认为的横向固有正应变，且角变形的大小与固有剪切应变的分布形式密切相关。

The project proposed and established the strict unique mathematical model of instantaneous frequency aiming at the currently existed problems in Hilbert Huang Transform form the viewpoint of physical connotative meaning; proposed and established the strict mathematical model of general intrinsic mode signal based on the concept of general continuous intrinsic mode signal and the compositive principle of practical general intrinsic mode signal; researched and proposed the fitting method of envelope lines in HHT from the viewpoint of theory, conquered the blindness and random in quondam EMD envelope line fitting and boundary treatment; developed a virtual time-frequency analyzer based on general intrinsic mode signal decomposition to open out the local time-frequency characteristics of nonlinear and nonstationary signal more deeply and accurately.

本项目针对希尔伯特-黄变换现阶段存在问题，从物理内涵的角度提出并建立了瞬时频率严格的唯一的数学模型；基于连续性的一般固有模态信号的概念和实际信号的一般固有模态信号的组成原理，提出并建立了一般固有模态信号严格的数学模型；从理论角度研究并提出HHT中的包络线构造方法，克服了原EMD的包络线构造和边界处理的盲目性和随意性；研发一台基于一般固有模态信号分解的虚拟式时频分析仪，使之可以更深入、准确地揭示非线性非平稳信号的时频局部特征。

The paper introduced the basic concept and theory of model analysis and structure dynamic analysis;performed the model analysis of the whole framework of hydraulic pressure and calculated the first ten-rank inherency frequency and corresponding vibratory-type;analyzed and estimated the first three-rank inherency frequency and corresponding vibratory-type of hydraulic pressure.

对液压机的整体机架进行有限元模态分析，得到了机架的前十阶固有频率和相应的固有振型，并对前三阶固有频率和振型进行了详尽的分析和评价。

In the modified Newtonian mechanics, the law of conservation of momentum and the law of conservation of energy become invalid; instead, the inherent momentum and inherent kinetic energy can be defined to make the law of conservation of inherent momentum and the law of particle inherent kinetic energy valid.

在修改后的牛顿力学中，动量守恒定律和能量守恒定律不再成立，但可以定义固有动量和固有动能，使得质点系固有动量守恒定律和质点固有动能守恒定律成立。

The natural twist vibration equation is set up by making use of the constitutive relation of nonlinear material.

利用非线性材料的本构关系，建立了非线性材料圆杆的扭转固有振动方程，然后采用傅立叶级数法求得了圆杆扭转固有振动的所似解，通过实例计算讨论分析了非线性材料圆杆的扭转固有振动特性。

The equations of dynamics for the balance are established by Kane's method, from which derives the characteristic equation of natural frequency by means of linearization of dynamic equations, and the six natural frequencies being developed according to the theory of vibration. The law of the six natural frequencies varying with mass of the upper platform and the stiffness of the elastic element are presented,and the Finite Element Method is employed to testify the validity of theoretical results.

基于 Kane 方法研究天平的动力学及模态，通过线性化动力学方程建立天平的固有频率方程，依据振动理论推导出并联天平的六阶固有频率及其对应的振型，同时研究了天平的六阶固有频率随敏感单元刚度系数及上平台质量的变化规律，并用有限元法验证理论计算结果的正确性。

Table 2.2 Infrastructure in different transport modes Road - Public No inherent guidance Infrastructure provided - Private Artificial, shared way centrally at public expense and at nominal cost to users Rail -Heavy Inherent guidance Track and control centrally - Light Artificial, dedicated way provided and charged to - Metro operators at full cost or owned by operators Air Natural, shared way Infrastructure provided by third party at full cost Maritime -Coastal/short Natural, shared way Infrastructure provided by sea No inherent guidance third party and charged at full Deep sea cost Inland water Natural or man-made Infrastructure provided by shared way third party and charged at full No inherent guidance cost Pipelines Artificial, dedicated way Infrastructure usually Inherent guidance provided by user All modes (except pipelines, although a travelator or moving walkway' may be considered a pipeline) carry both freight and passengers.

表2.2 不同运输方式的基础结构公路公共私人没有固有的牵引人造的，共享的方式基础设施由中央以公共费用和以使用者名义上的成本来提供铁路重型轻型地铁固有的牵引人造的，独占的方式铁轨和控制设施以完全成本的形式提供和向运营者收取费用或者由运营者所独有航空自然的，共享的方式基础设施由第三方提供并以完全成本方式收取费用海运沿海／近洋远洋自然的，共享的方式没有固有的牵引基础设施由第三方提供并以完全成本方式收取费用内河水运自然或人工的，共享的方式，没有固有的牵引基础设施由第三方提供并以完全成本方式收取费用管道人工的，专属的方式固有的引导基础设施通常由用户提供所有的运输方式（除了管道，尽管自动扶梯也可以被看作是一种管道）既能载人也能载货。

With Death guitarist Schuldiner adopting vocal duties, the band made a major impact on the scene.

随着死亡的吉他手Schuldiner接受主唱的职务，乐队在现实中树立了重要的影响。

But he could still end up breakfasting on Swiss-government issue muesli because all six are accused of nicking around 45 million pounds they should have paid to FIFA.

不过他最后仍有可能沦为瑞士政府&议事餐桌&上的一道早餐，因为这所有六个人都被指控把本应支付给国际足联的大约4500万英镑骗了个精光。