固定轴

The milling cutter is mounted on an arbor, where it is held in place by spacers or bushings.

铣刀装在心轴上，并用垫圈或轴套把它固定好。

Superior steering system Use hydraulic steering,decreases the fatigue of the driver greatly;the steering has the advantage of low noise and little leak; Use sross cylinder steering axle,its front and rear connector use ellipse design,and the connection with chassis adopted a block ofshock,largely reduces the shock of the truck.

优良的转向系统采用全液压转向器转向中大大减少操作者的疲劳；采用的转向器噪音低，内泄漏小的优点：采用横置油缸转向桥，前后连接轴采用椭圆型设计，与车架连接采用减震块固定，由刚性连接变为柔性连接，减少了叉车的震动。

Combining with the characteristics of membrane surface fulcrum system of Expo Axis, the main installation technologies are put forward, including installing external and middle masts synchronously fixed by temporary wind cable, installing horizontal cable firstly and backstays at last during construction.

结合世博轴膜面支点系统的特点，指出其主要安装技术路线，即外桅杆、中桅杆同步安装，临时缆风索固定，施工区间先安装水平索最后安装背索。

It has validated the system of high efficiency, safety, and stable quality. Zero- programming method can be used in NC process with fixed and limited parameters, such as gear grinding, gear shaper, and manufacturing of axis and disc parts.

零编程方法适用于编程参数和工艺参数固定、有限的数控加工，还可推广于齿轮加工的磨齿、插齿，以及轴类、盘类等零件的加工。

Mounted in gimbals, the gyroscopes' axes stay pointing in the same

固定在数个平衡环中的陀螺仪的轴始终指向同一个方向。

The company adopts silicon sol shell-making production process and have annual production capacity of 800ton high precision castings: High electric pure copper precision casting connector, lead brass top and bottom fixer of implement component, aluminum bronze trunnion of implement component hinge low alloy steel car rocker, high precision seamless component stainless steel polishing parts, resistant to the heat-treat steel casting impeller.

产品/Product：公司以全硅溶胶制壳工艺，形成年产1000吨的高质量精铸件的生产能力。产品为高导电纯铜精铸件连接器、铅黄铜电器元件上下固定器、铝青铜电器元件耳轴、铰链。低合金钢汽车摇臂、高精度工缝零件，不锈钢抛光件，耐热钢铸件，叶轮。

This process improves the appearance of a worsted fabric by removing fibrous material from the surface.a two-cylinder cutting machine is 英语翻译 in plate 51,whilst the principle of the action of the cutting parts is 英语翻译 in fig.43.the essential features arethe cutting—mower,together withthe ledger—blade,both andbeing positioned in a 商务英语报告格式,andthe bed over over which the cloth passes.there are also drawing rollers to pull the piece through the machine,a setting—up roller and several guides and tension meshanisms.the flocks shorn from the cloth are removed by a suction device.

这个过程通过从表面消除纤维状物质从而提高了精纺面料外观。每个两缸切割机总在51号板显现，虽然原则上该作用是在于43号切削部分。其重要特征是（1）切割部分，和（2）固定刀片，（1）及（2）两部分都被翻译在车头，以及（3）当织物通过时延伸到织物车床上。在滚轴作用下织物通过罗拉并被拉紧，成片毛屑从织物上被抽吸装置抽走。

The seat, disc and pivot pins are combined into one subassembly secured to the inlet side of the body with a locking ring in sizes 3 and smaller.

阀座，阀瓣和枢轴销构成一个分总成，采用尺寸3英寸或更小的锁环固定在阀体进口一侧。

In order to prevent misuse and the hand wheel being turned, you can set the security locking devices, for example, pin a fixed hand wheel to limit, or with a small locking wheel axle and so the top tight hand.

为防止手轮被误操作而转动，可设置安全锁紧装置，例如，销轴固定手轮进行限位，或用小锁紧轮顶紧手轮轴等。

Objective:To evaluate the value of localizing impacted teeth with lateral sagittal axial panoramic tomographs.

全景摄影技术是利用体层摄影和狭缝摄影原理而设计的固定三轴连续转换的体层摄影技术。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。