固定轴

Leave an indelible mark on the top wire, with an assortment of broacher out of 2mmX 5 mm platform, positioning and location circumrotating side type mount, locking the fixing screw.

在顶丝印记处用，什锦锉锉出2mmX 5mm的平台，将原定位轴、侧胶轮装入工位后，锁紧其固定螺丝。

Among these features are: absence of the nuclear rotation and development of the centriolar complex and the initial region of the axoneme in a position directly perpendicular to the basal pole of the nucleus and presence of numerous thick anchoring fibrils connecting the proximal centriole and the proximal part of the distal centriole to the nucleus.

其特点主要是：生精过程中不发生细胞核的旋转，中心粒复合体和轴丝起始段直接发生在核的基底面垂直线上，有无数的粗的固定纤维将近端中心粒和远端中心粒的近侧部连接到细胞核上。

Core adjusting rolling bearing type 22300 has 2rows of symmetry rolling spherical and copper alloy suppting frame,there is no fixed circlip in inner circle,the roller is the longer type,it has the abillity to support more load,the circlip will lead while moving,it has the better performance of core adjusting,also it can compensate the tolerance of coaxiai degree.

调心滚子轴承22300CA型具有两列对称球面滚子和铜合金实体保持架，内圈无固定挡边，滚子加长，承载能力大，活动中挡圈由内圈引导，调心性能良好，能补尝同轴度误差。

Install new rod, fixed by clevis pin and cotter pin.

安装新的阀杆，用销轴和开口销固定住。

Install new upper rod, fixed by clevis pin and cotton pin.

安装新的上阀杆，用销轴和开口销固定住。

Place gasket seal on the lower barrel, install upper valve rod and rod coupling, fixed by clevis pin and

把密封垫圈放在地下埋管上，安装上阀杆和连接套，用销轴和开口销固定住。

Length of the compages hoist jib is shown as fig.4-9, and set up them together by pins, after connected the first section and the second section, then install trolley and nacelle, and fixup them on the root of the hoist, and lay up the hoist on the support which has 1m height, so that the trolley and nacelle depart from the ground (shown as fig.4-11), then install the trolleying mechanism.

4.2.12.2 按照图 4-9 组合吊臂长度，用相应销轴把它们装配在一起，把第一节臂和第二节臂连接后，安上小车和吊篮，并把小车和吊篮固定在吊臂根部，把吊臂搁置在 1 米高左右的支架上，使小车和吊篮离开地面(见图 4-11)，装上小车牵引机构。

Length of the compages hoist jib pull rod is shown as fig.4-10d, connecting them by pins, fixup them on the corresponding supports which is chord rod of the hoist jib.

4.2.12.3 按照图 4-10d 组合吊臂拉杆长度，用销轴把它们连接起来，固定在吊臂上弦杆的相应支架上。

The sample spectra were obtained with the cuvette holder in-line between the fibers.

样品光谱是通过将小型管固定器与纤维之间同轴的方式获得的。

It's just a matter of hooking the device to the battery and fixing the sensor and it's metal plate on the end of the prop shaft closest to the transfer box.

这只是一个挂接装置对电池的问题和固定的传感器和它的对金属板支撑底轴最接近交接箱。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。