固定轴

The Flex-Hone tool should be securely held in a collet, chuck, or similar holding device. It is best to use the shortest shank possible for your application.

球头刷应该被安全地固定在筒夹、卡盘或其他类似的固定装置上，最好使用尽可能短的轴杆。

In Fig.1,spindle A is supported by two identical isotropic bearings in radial direction;spindle A and drill clamp C D is connected by shaft B;micro-drill E F is fixed in the clamp D.Drill part with the screw slots is taken as uniform shaft F by equivalent of the bending stiffness.

In ，主轴A是支持的两个相同的各向同性轴承径向方向；主轴A和演习钳的C - D的连接轴B组；微型钻电子F是固定在钳4钻部分螺钉插槽是采取统一轴F相当弯曲stiffness。

The method is as follows that the two ends of a nanometer are fixed on two pivots and an axial micro-pulling force T is applied on the nanometer; an electrode is arranged on the middle part of the side of the nanometer and an alternate voltage is applied on the electrode to motivate the nanometer to generate resonance, and therefore, the natural frequency f of the nanometer is measured and acquired; according to the material characteristics and the geometry characteristics of the nanometer as well as the boundary condition of the nanometer material, the relation between the natural frequency and the axial pulling force of the nanometer, namely the f-t curves of the nanometer, can be calculated by a vibration equation; according to the measured natural frequency f, the size of the micro-pulling force T can be acquired.

该方法将一根纳米材料的两端固定在两个支点上，给纳米材料施加一个轴向的微小拉力T；在纳米材料的侧面，位于该纳米材料的中部放置一个电极，在电极上施加一个交变的电压激励纳米材料使其发生共振，测得纳米材料的固有频率f；根据纳米材料的材料特性和几何特征以及纳米材料的边界条件，由振动方程计算出该纳米材料的固有频率与所受的轴向拉力的关系，即纳米材料的f-T曲线；根据上述测得的固有频率f，得到微小拉力T的大小。

Because the crank is connected with the shaft through the flat key and the shaft is fixed onto the valve plate with the pin, thus the valve plate is driven to turn in the valve body so as to change the flow area of the pipeline change to regulate the flowrate of the medium.

由于曲柄通过平键与轴连结，。轴与阀板用销子固定，从而带动阀板在阀体内回转，使管道流通面积变化，达到调节介质流量。

Based on the clinical and radiological results the authers believe that lag screw technique is a feasible method for indicated condylar fracture.

轴向拉力螺钉复位固定技术对于固定髁突骨折、恢复髁突的生理功能，防止相应并发症是行之有效的。

The encoder body is fixed by means of two flexible mountings which compensate for minor shaft misalignment.

编码器是固定的机构通过两个灵活的固定的补偿轻微轴偏心。

The computationresults show that for a organ-pipe nozzle with a given configuration size, the nondimensional axial velocity attenuates slower with the increase in stand-distance, and the nondimensional axial velocity attenuation pattern remains the same, and the nondimensional axial velocity along the jet centerline attenuates slower with the increase in distance between the nozzleexit and the impinging plate.

计算结果还表明：对给定结构尺寸的风琴管喷嘴，随着喷距的增加，沿径向的无因次轴向速度衰减变慢、沿径向无因次轴向速度衰减规律不随喷速的变化而变化；无因次轴心速度的衰减规律随着喷嘴出口到井底间距离的增大，射流轴心速度衰减变慢，但其变化幅度不大；在固定靶距情况下，无因次轴心速度衰减规律不随喷速的变化而变化。

OBJECTIVE: From the rheological point of view to quantitatively analyze the two fixators in clinical application of the treatment of spinal fracture-dislocation through simulation of spinal L1-2 fracture-dislocation and axial compression test after plate and intramedullary nail fixation.

目的：通过模拟脊柱L1~2骨折脱位，以钢板和髓内钉固定后对标本进行轴向压缩应力松弛实验，从流变学角度对临床治疗脊柱骨折脱位的2种固定器进行定量分析。

OBJECTIVE: From the rheological point of view to quantitatively analyze the two fixators in clinical application of the treatment of spinal fracture-dislocation through simulation of spinal L1-2 fracture-dislocation and axial compression test after plate and intramedullary nail fixation.

目的：通过模拟脊柱L(下标 1~2)骨折脱位，以钢板和髓内钉固定后对标本进行轴向压缩应力松弛实验，从流变学角度对临床治疗脊柱骨折脱位的2种固定器进行定量分析。

A compressor is disclosed generally comprising a housing, a shaft disposed therein, and a swash plate part that is mounted at a fixed angle relative to the longitudinal axis of the shaft.

本发明公开了一种压缩机，该压缩机包括壳体、设置在所述壳体中的轴和相对于轴的纵向轴线以固定倾角安装的斜盘部分。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。