因数

Finally, we simulate the relationship of the residuary intensity modulation coefficient and the scale factor stability of fiber-optic gyro by using the Matlab simulation tool. The simulation results further explain the effect of residuary intensity modulation on digital closed-loop fiber-optic gyro scale factor stability.

最后，对所得出的残余强度调制系数与光纤陀螺标度因数稳定性的关系进行了Matlab仿真，通过仿真结果，更进一步说明残余强度调制对数字闭环光纤陀螺标度因数稳定性的影响。

The purposes of this study are to develop two concrete teaching activities and to see students' learning situations from practicing the activities of divisor's unit.

本研究旨在发展因数教学活动设计以帮助学生理解因数的意义，并从实践中了解此教学活动的学习情形。

Friction coefficients and lubricative mechanics of Al-Fe-V-Si heat resistant aluminum under four conditions were researched by method of annulus compression, without lubricant, but in the presence of pure aluminum, graphite+oil, pure aluminum+graphite+oil.

摘 要：采用圆环压缩法检测Al-Fe-V-Si系合金在喷射沉积高温时变形的摩擦因数，研究未加润滑剂、加石墨+机油润滑、加纯铝润滑、加纯铝+石墨+机油润滑4种条件下的摩擦因数随变形温度变化的情况，并探讨其润滑机理。

They are FF testing methods, surface treatment technique, evaluation of the properties of surface modification layer, coating induced embrittlement, selection of coating materials, effects of SP and other surface modification on fretting fatigue resistance . A new coating technology combined with shot peening is proved in improving FFR of titanium alloy. The relation between fretting wear and fretting fatigue mechanism of titanium alloy are discussed on the basis of the experimental results. The main contributions are as follows:(1) Shot peening is the most efficient way in improving fretting fatigue resistance of titanium alloys. Working hardening, roughening and compressive residual stress are involved in the shot peened surface.

本文针对上述问题，从影响FF行为的关键环节：FF实验方法、表面处理工艺技术及表层性能评价、镀层引起的钛合金脆化行为、脆化机制及镀层材料的选择、喷丸强化因数和表面涂层对钛合金FF抗力的影响、FF与微动磨损的联系等，深入系统地研究影响钛合金FF抗力的控制因数，探讨FF机理，并通过喷丸形变强化与新型表面镀或渗层合理复合，达到进一步提高钛合金FF抗力的目的。

The numerical results show that: the stress distribution on contact surface is relative to the relative velocity of sliding block and friction coefficient, and the maximum relative error of stress can be 100.08%. The non-linear Stribeck friction model can better describe the real situation of contact surface, because of the consideration of impact of the relative velocity to the friction.

研究结果表明：随着接触体相对速度的改变，摩擦因数相应变化，接触面上的应力与位移的分布随之改变，应力最大相对误差达100.08%；Stribeck模型考虑了速度对摩擦因数的影响，更能描述接触的真实情况。

Influence of Additional Twist on Flax Cotton Blended Compact Yarn Property;2. By numerical integral of this model, the factors which affect the additional twist of yarn are analyzed, including the pressure in the profile tube and the coefficient of friction between the fiber band and lattice apron.

通过对集聚区内须条的集聚过程分析，建立须条变截面部分的力学模型，可以得出此部分须条是有附加捻度的，并且对影响这部分须条附加捻度的因素：须条与网格间的摩擦因数和负压的大小进行了分析，结果表明集聚区须条的附加捻度随着须条与网格间的摩擦因数和负压的增加而增加。

Based on finite element dynamic model of expansion casing with rubber sleeve, casing deformation and stress change inside casing, contact pressure at both sides of rubber sleeve and expansion parameter changes caused by friction factors during the expansion are analyzed.

根据带有橡胶筒的膨胀套管有限元力学模型，对套管膨胀过程中橡胶变形和套管内的应力变化、橡胶筒两侧的接触压力，以及摩擦因数引起的膨胀参数变化等做了分析研究；对橡胶筒的厚度、长度做了定量和定性分析，发现在橡胶与套管之间的接触摩擦因数作用下，橡胶过长将会在纵向产生&堆积&现象，在有限空间中，使其受较大的接触压力而失效。

The experimental results indicate that friction coefficient of the Cu-MoS2 powder met...

研究结果表明：在有电流条件下，加入MoS2可显著降低铜基粉末冶金/铬青铜配副的摩擦因数和铜基粉末冶金材料磨损率，10%和20%MoS2含量的粉末冶金试样的磨损率相差不显著，20%MoS2含量的摩擦因数在高速时有所增加。

It is indicated that the dielectric loss factor of the epoxy resin impregnated paper insulating bushing is generally higher than thatof the oil impregnated paper insulating bushing of the same voltage level; the tests should be strengthened when notable variation is found in the insulation dielectric loss factor and capacitance; when the variation is greater than 10%,the bushing must be replaced.

最后指出，环氧浸纸绝缘套管的介质损耗因数普遍高于同等电压等级的油浸纸绝缘套管，当发现绝缘介质损耗因数和电容值发生较明显变化时，应加大测试密度，当变化量大于10%时，必须更换套管。

Tested the volatilization of boron through the acid-alkali neutralization titration, analyzed the influencing factor of boron volatilization, the conclusion showed that the moisture content and heating-up time were important factor; observed the phase splitting by the SEM, the conclusion showed that the phase splitting were all connected state.

通过酸碱中和滴定法测定了硼挥发量，分析了影响硼挥发的因数，结果表明含水量和升温速率是影响硼挥发的重要因数；通过扫描电镜观察了玻璃的分相情况，结果表明其分相类型均为连通状分相。

The labia have now been sutured together almost completely.The drains and the Foley catheter come out at the top.

此刻阴唇已经几乎完全的缝在一起了，排除多余淤血体液的管子和Foley导管从顶端冒出来。

To get the business done, I suggest we split the difference in price.

为了做成这笔生意，我建议我们在价格上大家各让一半。