回转中心

The correction of deviation of real gyration center from design gyration center and the calibration method of the measuring tool are analyzed.

研制了一种可精确测量大型圆锥体工件外锥面与端面交线尺寸的专用量具，介绍了量具结构及测量原理，分析了量具实际回转中心偏离设计回转中心的修正原理及检定方

By analyzing and comparing the monitoring technique of rotary kilns axis at present at home and oversea, this paper puts forward a brand-new monitoring method of more advance and more scientific, that is the keyway-phase measure in direction of null displacement of the center of gyration measuring.

本文通过对国内外现有回转窑轴线临测技术的分析和对比，提出了一种更先进、更科学的全新的监测方法，即回转中心测量零位移方向键相法。

The combined motion of grinding the transition arc maintains that the gyration center of the arc moves along the parallel line to the surface of the grinding wheel, and the gyration center of the oxide tool moves along the vertical line to the surface of the grinding wheel.

磨削刀片过渡圆弧时，过渡圆弧的回转中心到砂轮面的距离必须恒等于过渡圆弧的半径，磨削过渡圆弧的复合运动要保持过渡圆弧的回转中心沿平行于砂轮面的直线运动；刀片的回转中心沿垂直于砂轮面的直线运动。

The injection holder may round center of gyration for certain angel, which brings convenience to install/remove the screw, rinse the barrel and install the mold.

注射座可围绕回转中心扳转一定角度，以便装拆螺杆，清洗料筒，及方便安装模具。

There were the same load characteristics of 1MW, 1.5MW and 2MW blade model, which the tensile stress, shear stress and torque of section were linearly increased with increasing of wind speed; and tensile stress of all test sections of the blade was changed greatly, but shear stress was basically the same in the same wind speed. The shear stress and tensile stress were increased obviously in the place of 388mm to centre of gyration of wind rotor comparing with other section where the phenomenon of stress concentration had for 1.5MW blade model.

对1MW、1.5MW、2MW叶片模型有相同载荷特性，各截面处的拉应力、剪应力、扭矩随风速增大而增大，呈线性增加规律；在相同风速下，叶片各测试截面的拉应力值变化较大，而剪应力值基本相同，但对1.5MW叶片模型，在距风轮回转中心388mm处与其它截面处的剪应力、拉应力比较明显增大，有应力集中现象。

Because the workpiece is in dynamic balance, the resultant moment acting on it should be zero. Introducing the moment from lapping tool and press head a moving differential equation is built. In this equation only workpiece rotating speed is unknown. It means that workpiece rotating speed can be got by this equation. Since there is a transcendental function in integral function of the equation an analytic result can not be got, only digital result can be got by a computer. Thus a change rule of workpiece rotating speed with lapping parameters is known, e.g. the radius of press disc ball socket, radius of press head ball, the distance between the workpiece rotating axis and lapping tool rotating axis, workpiece radius, modulus of elasticity of the press head and press disc, friction coefficients between the lapping tool and workpiece, and between the head and disc, pressure between the lapping tool and workpiece and pressure between the press head and press disc.

因工件处于动态平衡状态，其上所受到的来自于磨具和压头的力矩应相等，将二力矩表达式联立，建立工件运动微分方程，该方程中只有工件的旋转角速度是未知量，因此可以求出工件旋转角速度，但该方程积分式中含有超越函数，得不出解析解，只能通过计算机求出数值解，得出工件旋转角速度随各研磨参数的变化规律，如压盖球座半径、压头的球头半径、工件回转中心相对磨具回转中心的偏心距、工件半径、压头和压盖材料的弹性模量、磨具与工件间的摩擦系数、压头压盖间的摩擦系数、磨具与工件间的压强、压头压盖间的压力等。

Third, in processing, the arc length of cutter on the pitch curve was equal to be the length of cutter rotating around its axis in order to guarantee the generating between the pinion cutter and the blank.

第三，在加工过程中，为保证刀具和齿坯之间的范成关系，刀具在齿坯节曲线上滚过的弧长等于刀具绕其自身回转中心转过的弧长。

The method is :there are two perpendicular axes whose distance are controlled ,one is the axis of work table, the other is fixed with a microscope for aiming.

该测量方法是：两个相互垂直且间距可调的数控回转轴，一轴与工件的回转中心重合，另一轴上固定可移动的瞄准显微镜，当显微镜瞄准被测孔时，两轴的转角由各自的圆光栅测出，两轴之间的角度位置确定曲面壳体零件上小孔的孔位置，同时采用CCD摄像头，利用图象处理技术实现小孔的尺寸测量。

In singular or a small amount manufacture , change and correct of craft equipment are difficult when turnery that is not concentric is manufactured .

在车床上加工偏心工件，主要是在装夹方面采取措施，只要把轴线调整到与车床主轴回转中心重合即可。

Based on the hypothesis that the connecting line of two turning centers bisects the connecting line of two geometrical centers, the analysis and design equations of eccentric involutes gears transmission are established.

基于两齿轮的几何中心连线等分回转中心连线的假设，建立了偏心渐开线齿轮传动分析和设计方程，分析了模型的误差。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。