回转

SZG series double cone rotating vacuum drier's main machine is double cone tank, let steam or heat water inside sealed jacket heat the inner shell in vacuum state, the hot transferred from inner shell to dump material, make water of the dump material gasify, low speed motor drying the tank along, make material up and down, from inside to outside, and change the heated surface, at the same time, vapour is taken out continually through vent-pipe of vacuum pump, increase the speed of drying, attain the purpose of uniformity drying at last, it is in conformity with the requirement of GMP.

SZG双锥回转真空干燥机主机为双锥形罐体，罐内在真空状态下，夹套内可通过内胆传递给湿物料，使湿物料中水分气化，低速电机带动罐体回转，物料不断上下内外翻动，更换受热面，同时，水蒸气通过真空泵经真空排气管不断被抽走，加快了物料干燥速率，最终达到均匀干燥的目的。符合药品管理规范"GMP"的要求。

1 Equipment of powder materials treatment: Reduction furnace for metal powder( including push rod type, steel strip type and net strip type), device of ammonia decomposing (dew point or flux feedback control type), rotary motion double cone vacuum dryer, whole set of equipment of high pressure water atomizer, whole set of gas atomizer, whole set of equipment of vacuum gas atomizer( vacuum immediate frequency induction melting furnace included), rotary motion calcine kilnpatent awarded

粉体材料处理设备：金属粉末还原炉（推杆式、钢带式、网带式），氨分解发生器（可选配露点、流量反馈控制型），回转双圆锥真空干燥器，成套高压水雾化设备，成套气雾化设备，成套真空雾化设备（含真空中频熔炼炉，实现炉温反馈控制），回转锻烧炉。

Based on the basic concept and nomoment theory of rotational shell,the geometry and membrane stresses of the ellipsoidal head are discussed in this paper.

根据回转壳体的基本概念及回转薄壳的无力矩理论，探讨了椭圆封头的几何形状及其薄膜应力等问题。

Numerical calculation shows that the mean-square radius of gyration of hyperbranched copolymer decreases greatly compared with the analogous linear polymer even if the degree of branching is very small.

这是因为整个体系的Z均均方回转半径不仅和每个分子的均方回转半径有关，还和分子量的分布有关。

Gyrator is one of the important work of drilling rig, its main function is to drive rotary drill, drill effectively broken rock to provide a reasonable speed and torque.

回转器是钻机的重要工作机构之一，其主要功用是带动钻具回转，为钻头有效地破碎岩石提供合理的转速及转矩。

Gyrator is used mainly driven rotary drill, and drill through the feed tank to achieve decompression of drilling increases.

回转器主要是用来带动钻具回转，并通过进给油缸实现钻具的加减压钻进。

Gyrator mainly by the following components: vertical, vertical conduits gyrator box, connecting plates, pressing beam, cylinder, bevel gear and other large arc.

回转器主要由以下几部分组成：立轴、立轴导管、回转器箱体、连接盘、压梁、油缸、大圆弧锥齿轮等。

The computer simulation software was developed for figuring the path curves and instantaneous speed of the lapping process.

文中从运动学和几何学原理出发，建立了工件精密研磨过程的轨迹方程，通过将复杂的研磨运动简化为在中心距一定条件下夹具绕研磨盘中心轴的回转运动及夹具自身的回转运动，对工件上任意点相对于研磨盘的运动轨迹及瞬时速度进行了分析计算，并开发了相应的计算机仿真软件，对其运动轨迹曲线及瞬时速度进行了分析。

Because the workpiece is in dynamic balance, the resultant moment acting on it should be zero. Introducing the moment from lapping tool and press head a moving differential equation is built. In this equation only workpiece rotating speed is unknown. It means that workpiece rotating speed can be got by this equation. Since there is a transcendental function in integral function of the equation an analytic result can not be got, only digital result can be got by a computer. Thus a change rule of workpiece rotating speed with lapping parameters is known, e.g. the radius of press disc ball socket, radius of press head ball, the distance between the workpiece rotating axis and lapping tool rotating axis, workpiece radius, modulus of elasticity of the press head and press disc, friction coefficients between the lapping tool and workpiece, and between the head and disc, pressure between the lapping tool and workpiece and pressure between the press head and press disc.

因工件处于动态平衡状态，其上所受到的来自于磨具和压头的力矩应相等，将二力矩表达式联立，建立工件运动微分方程，该方程中只有工件的旋转角速度是未知量，因此可以求出工件旋转角速度，但该方程积分式中含有超越函数，得不出解析解，只能通过计算机求出数值解，得出工件旋转角速度随各研磨参数的变化规律，如压盖球座半径、压头的球头半径、工件回转中心相对磨具回转中心的偏心距、工件半径、压头和压盖材料的弹性模量、磨具与工件间的摩擦系数、压头压盖间的摩擦系数、磨具与工件间的压强、压头压盖间的压力等。

When installing, dismantling and adjust the slewing mechanism, notice that ensure the center line of slewning mechanism reducer is paralleled with the center line of thegear wheel, and its joggle should less than 70% of its area, and the clearance of joggle should be suitable.

9.1.7 安装，拆卸和调整回转机构时，要注意保证回转机构减速器的中心线与齿轮的中心线平行，其啮合面不小于 70%，啮合间隙要合适。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。