回转

Based on the reasonable simplification and assumption for slewing ring in mechanical engineering, calculating the pressure on unit length of arc at any angle of raceway under different loads of slewing ring .

在对工程机械中常用的回转支承装置进行合理的简化和假设后，根据其受力状况，分别计算出作用在回转支承上的各种载荷对滚道圆周上任意角处单位弧长上所产生的压力，最后应用压力叠加的方法，推导出回转支承装置摩擦阻力矩的计算公式。

The combined motion of grinding the transition arc maintains that the gyration center of the arc moves along the parallel line to the surface of the grinding wheel, and the gyration center of the oxide tool moves along the vertical line to the surface of the grinding wheel.

磨削刀片过渡圆弧时，过渡圆弧的回转中心到砂轮面的距离必须恒等于过渡圆弧的半径，磨削过渡圆弧的复合运动要保持过渡圆弧的回转中心沿平行于砂轮面的直线运动；刀片的回转中心沿垂直于砂轮面的直线运动。

Based on the analysis to crankshaft-working system and turning/feed system for cold pilger mill and radio of two turning angles, the system is designed with computer.

本文通过对双回转送进二辊冷轧管机的曲轴机架与回转系统进行分析，以保证工作行程和轧件两次回转角分配比为设计前提，按照回转凸轮轮廓曲线的两过渡段的峰值加速度相等的设计准则，计算曲轴-机架与回转系统，实现了系统的最优化的设计。

If the kiln should stop to Overhaul, work should be down, and make a heavy economic loss. As a part of kiln measure, the kiln"s ovality measure can reflect the status of kiln"s firebrick and shell.

作为水泥回转窑检测的一部分，椭圆度的测量，可以很好的反映出水泥回转窑的衬砖和筒体状况，从而对回转窑的运转情况，提供一个很好的指导数据。

The discrete mathematical models of the roundness and cylindricity EST are established; the mathematical models of the generating line straightness, axis straightness, coaxality, circular run—out and total run—out error of the revolution workpiece are put forward and established first based on the EST; the method about how to sample and to process sampling data are given when these models are applied to measure workpleces.

其主要内容是：针对长期以来国内对回转误差运动的有关定义的争论，对回转误差运动的本质进行了讨论，进一步明确了静心与静轴，动心与动轴的概念，并对此进行了数学推导，给出了相应的数学模型；统一了"平动说"和"瞬心说"关于回转轴线的定义，指出了两种学说各自的力学基础和它们的一致性。

Derives the formulae for calculating the distortion and stress on the acting surface of flexspline load in the drive process of the harmonic gear drive with three-wave wavegenerator;(2) analyzes and compares the performance of plastic and steel products under light load drive and calculates the probably reached limit of drive ratio for both types of flexsplines under the same load;(3) applies the harmonic gear drive with three-wave wavegenerator to the small-sized multiple-revolution electric device of valves by taking into consideration of the low limit of the drive ratio for the harmonic gear drive with three-wave wavegenerator made of plastics, improves the design on the main drive mechanism of the traditional small-sized multiple-revolution electric device of valves, and validates through examples the feasibility for the harmonic gear drive with three-wave wavegenerator made of plastics to be applied to the small-sized multiple-revolution electric device of valves. Finally the author performs calculations on the two types of the flexsplines of the harmonic gear with three-wave wavegenerator by using the finite element method and analyzes the causes for the errors.

本文根据三波谐波齿轮传动的运动变形特点，采用弹性薄壳的力矩理论，推导了三波谐波齿轮传动柔轮载荷作用面上的变形及应力计算公式；分析比较了轻载传动情况下塑料和钢材的性能，计算了塑料制谐波柔轮和钢制谐波柔轮在相同载荷情况下可能达到的传动比极限；对塑料制及钢制三波谐波齿轮柔轮进行了有限元计算，分析了产生误差的原因；针对三波塑料谐波齿轮传动比极限低的特点，将之运用于小转矩多回转阀门电动装置中，对传统的小型多回转阀门电动装置的主传动机构进行了改良设计，并通过实例验证了三波塑料谐波齿轮传动在小转矩多回转阀门电动装置中应用的可行性。

First, this article introduced 2 grade of rotary kiln principle of work and the equipment, to rolled the circle mechanics behavior to carry on the analysis, proposed - rolled the circle - under roller's rotary kiln overall modelling based on the tube body - kiln liner - big tooth ring, to rolled the circle - under roller's contact stress to carry on the finite element analysis the method, and obtained rolled the circle contact stress the size and the distribution rule, finally indicated that rolled the circle contact stress mainly to have two main peak values and the sudden change in one week, appeared is rolling the circle and the under roller contact area; Then, rolls the circle the stress to regard as is the principal stress unknown plane stress test, the use quite mature modern test technology, proposed rolls the circle stress test the principle and the plan, and to rolled the circle the stress to carry on the scene test, the stress which the scene test analysis result and the finite element analysis calculated has compared, had proven the whole method modelling's finite element analysis method's rationality and rolled the circle - under roller contact stress the result accuracy; Finally, uses ANSYS APDL the re-development technology, in view of 2 grades of rotary kilns, rolled the circle - under roller contact stress the overall finite element analytic method to carry on the re-development.

首先，本文介绍了2档回转窑工作原理和装置，对滚圈的力学行为进行了分析，提出了基于筒体-窑衬-大齿圈-滚圈-托轮的回转窑整体建模，对滚圈-托轮的接触应力进行有限元分析的方法，并得到了滚圈接触应力的大小和分布规律，结果表明滚圈接触应力在一周内主要存在两个主要的峰值和突变，都出现在滚圈与托轮接触区域；然后，把滚圈的受力看成是主应力未知的平面应力的测试，利用比较成熟的现代测试技术，提出了滚圈应力测试的原理和方案，并对滚圈的应力进行了现场测试，现场测试分析结果与有限元分析计算出的应力相比较，证明了整体法建模的有限元分析方法的合理性和滚圈-托轮接触应力的结果的正确性；最后，利用ANSYS的APDL的二次开发技术，针对2档回转窑，就滚圈-托轮接触应力的整体有限元分析法进行了二次开发。

Firstly, the paper introduced the working principle and device of the two-pass grate-rotary kiln and had an analysis method of mechanics of the tyre. We have put forward the finite element analysis of the contact stress of the tyre-roller based on the whole construction mode of shell-kiln liner-large gear-tyre-roller of the rotary kiln and obtained the strength and distributing rule of the tyre's contact stress. The research shows that within one week the contact stress mainly lies in two leading peak value and catastrophe which appear at the contact zone of the tyre and supporting roller. Then we regarded the tyre's stress as the test of unknown plane stress of principal stress. Utilizing mature and modern testing technology, we raised the testing principle and scheme of tyre stress and then had a on-the-spot test of the stress. Comparing the analysis result of the test with the one calculated from the finite element analysis, it proofed the rationality of finite element analysis method of integral modeling and the correctness of the contact stress result of the tyre and roller. Finally, for two-pass of similar rotary kilns, using the ANSYS APDL re-development technology, carried on the re-development about the overall finite element analytic method of thecontact stress of tyre-roller.

首先，本文介绍了2档回转窑的工作原理和装置，对滚圈的力学行为进行了分析，提出了基于筒体-滚圈-托轮的回转窑整体建模的有限元分析法，来对滚圈-托轮的接触应力进行有限元分析与计算，得到了滚圈接触应力的大小和分布规律，并求得滚圈外中内圈节点的主应力；其次，把滚圈的受力看成是主应力未知的平面应力的测试，利用现代测试技术，提出了滚圈主应力测试的原理和方案，并对滚圈的主应力进行了现场测试，现场测试分析结果与有限元分析计算出的主应力相比较，证明了整体法建模的有限元分析方法的合理性和滚圈-托轮接触应力结果的正确性；最后，利用ANSYS的APDL的二次开发技术，针对2档同类回转窑，就滚圈-托轮接触应力的整体有限元分析法进行了二次开发。

Took the different diameters double-row bearing slewing ring asexample, this dissertation studied the distribution of axial press ofthe rolling body under axial load and throw moment, the contact pressbetween two outer seat-rings which are connected to the main machinewith high strength screw bolts.

本文以双排异径球式回转支承为例，对球式回转支承在承受轴向载荷和倾翻力矩时的滚动体轴向正压力大小、分布及由高强度螺栓与主机连接的滚圈接触面的接触力进行了详细的理论推导和实际计算，说明在双排球式回转支承的结构静力分析过程中，可以将滚圈安装接触面的接触力简化为铅垂方向的均布载荷。

Therefore, through the thermodynamic analysis and calculation of calcining active calcareousness rotary kiln in Pan Zhihua Steel Factory, the relationships among rotary kiln efficiency, output and gas-fired quantity could be concluded.

因此，本文通过对攀钢煅烧活性石灰回转窑进行了热力分析计算，得到了回转窑效率、产量、燃气量等之间的关系，通过对各影响参数的了解，可以掌握回转窑的热工制度，同时也可以掌握熟料的煅烧状况。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。