回收系统

Based on the temperature and humidity control air-conditioning system, this paper proposes the concrete scheme which recyclies the heat dissipation of the condenser part of air cooled heat pump unit to regenerate solution and proves the energy-saving effect.

基于温湿度独立控制溶液除湿空调系统，作者提出回收利用风冷热泵机组的冷凝器部分散热用来进行溶液再生的具体方案，并进行了节能效果的论证，发现再生器中消耗的热量可以节省15%左右，节能效果显著。

Recently it has been a hotspot in airdrop and recovery. But its academic research could not keep up with its development in engineering.

目前翼伞系统已成为空投和回收领域研究的热点，但理论研究的水平还远不能满足工程应用的需求。

The tank is equipped multiplex safety devices and instruments: Imported combination of pressure gauge and liquid level meter, interlayer equipped with outer cylinder explosion-proof device, the inner barrel equipped with combined safety system (combination system of double safety valve bursting diaphragm), discharge outlet of the safety valve and air valve adopting centralized collecting piping and discharging through the fire barrier

罐体设置有多重安全装置和仪表：配置进口压力表液位计组合，夹层设有外筒防爆装置，内筒设有组合安全系统（双安全阀爆破膜组合系统），安全阀和放气阀的排放口采用集中回收管道通过阻火器进行排放

Auxiliary Equipment Dryers, Grinders, Metering and Feeding Devices, Heaters, Mold Releasers, Mold Temperature Controllers and Coolers, Sensors, Monitors, Screws and Cylinders, Recycling Equipment and Systems, Testing Equipment and Instruments, CAD/CAM systems, etc.

辅助设备干燥机，研磨机，计量喂料装置，加热器，模具装卸，模温控制器及冷水机，传感器，监控仪器，螺杆机筒，回收设备及系统，检测设备及仪表，CAD/CAM系统等等。

Auxiliary EquipmentDryers, Grinders, Metering and Feeding Devices, Heaters, Mold Releasers, Mold Temperature Controllers and Coolers, Sensors, Monitors, Screws and Cylinders, Recycling Equipment and Systems, Testing Equipment and Instruments, CAD/CAM systems, etc.

辅助设备干燥机，研磨机，计量喂料装置，加热器，模具装卸，模温控制器及冷水机，传感器，监控仪器，螺杆机筒，回收设备及系统，检测设备及仪表，CAD/CAM系统等等。

Auxiliary EquipmentDryers, Grinders, Metering and Feeding Devices, Heaters, Mold Releasers, Mold Temperature Controllers and Coolers, Sensors, Monitors, Screws and Cylinders, Recycling Equipment and Systems, Testing Equipment and Instruments, CAD/CAM systems, etc.

干燥机，研磨机，计量喂料装置，加热器，模具装卸，模温控制器及冷水机，传感器，监控仪器，螺杆机筒，回收设备及系统，检测设备及仪表，CAD/CAM系统等等。

Some valuable conclusions were drawn and shown as following: Three models were brought forward, i.e. 6DOF rigid-connected model, 8DOF rigid-jointed model and 12DOF non-rigid connected model. The basic dynamic properties of the system, the relative motion between parafoil and payload, and some geometric parameters'effects on the system dynamics were analyzed and summarized.

分别建立六自由度刚性连接模型、八自由度刚性铰接模型和十二自由度非刚性连接模型，着重分析了系统的基本运动特性、回收物-伞体间的相对运动特性，以及主要设计参数对系统性能的影响；并将不同复杂程度的模型进行对比，分析了各种模型的特点和适用范围。

Refined into the present company main products: heating categories: thermostatic radiator valve, balance valve, self-acting differential pressure controller, self-traffic controllers, self-operated valves, electric control valve, to warm temperature controller, desuperheating decompression system; air conditioning products: indoor temperature controller, electric Two-, three-way valve, pressure bypass control systems, proportional-integral-type regulating valve and so on; treatment series of products: electronic water treatment device, filter backwashing , and condensed water recovery unit and other hydraulic control valves.

目前精成公司主要产品有：供暖类：散热器恒温阀、平衡阀、自力式压差控制器、自力式流量控制器、自力式温控阀、电动调节阀、地暖温控器、减温减压系统；空调类产品：室内恒温控制器、电动二通、三通阀、压差旁通控制系统、比例积分式调节阀等；水处理系列产品：电子水处理仪、反冲洗过滤器、冷凝水回收装置及其它水力控制阀门。

After fully heat-exchanged inner individual processes, the further integration for heat sources and heat sinks of processes with utility system of steam-power cogeneration was made, including the balance between energy use and heat recovery, cogeneration of steam and power, optimization of steam levels, and synthesis of turbine networks.

在实现各过程内部热量交换的基础上，进行各过程之间的剩余热阱和热源与蒸汽动力系统的全局能量集成，包括废热回收、热功联产、蒸汽系统设计和透平网络综合。

The process driving force and the energy-saving potential were presented in the phosphorous acid production by BEP.

本文以有余热回收的两步法热法磷酸生产系统为研究对象，提出了热法磷酸生产过程推动力及其节能潜力的概念和计算方法，通过对实际生产系统进行的能量分析，说明了考虑过程推动力的能量分析的科学性和实用性。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐