回弹

Springback is considered in the design of the bending die , since there is a big bending radius .The third die is wedge clicker die .

第二副模具为弯曲模，由于有一个较大的弯曲半径，所以在设计中主要考虑回弹因素对成形精度的影响。

Springback isconsidered in the design of the bending die ,since there is a big bending radius .The thirddie is wedge clicker die .

第二副模具为弯曲模，由于有一个较大的弯曲半径，所以在设计中主要考虑回弹因素对成形精度的影响。

In addition, the imitation method of spin-up and spring back drag loads for column style drop test-bed is discussed, and determined the reasonable imitation style, perfected drop test technology.

另外，本文对国内立柱式落震试验台的起转和回弹载荷模拟方法进行了研究，确定了合理的模拟方式，完善了落震试验技术；通过模拟起落架落震试验的钢球冲击钢板的冲击实验，对机轮垂直载荷的精确测量问题进行了初步的研究；研制了一套监测起落架投放高度的测量系统；用Turbo C和VC++6.0编写了落震试验数据采集和处理系统的应用软件。

On the base of large amount of tests, this thesis analyzes the impacts of testing period, fiber dosage and cement dosage upon the compressive strength, splitting tensile strength, compressive resilient modulus, flexural strength and flexural elastic modulus of polypropylene fiber cement stabilized macadam, and the corresponding impact rule was found.

3在大量试验的基础上分析了试验龄期、纤维掺量、水泥掺量对聚丙烯纤维水泥稳定碎石抗压强度、劈裂抗拉强度、抗压回弹模量、抗弯拉强度和抗弯拉弹性模量等的影响，并得出了相应的影响规律。

Turn your rebound adjusters in to the full stiff position and push down on the suspension.

转动你车的回弹阻尼调节器到最硬的位置，然后压下减震。

First off, Ricky should set his rebound adjusters as outlined in the setup section, and back the compression adjusters out to no more than the middle of their range.

首先， Ricky 应该调节他的回弹阻尼，并且调的压缩阻尼到不超过调节范围的一半的地方。

This article firstly introduced the development history of digital simulation technology and spring-back, retrospected the researches about this by scholars in-and out-country, and then related theoretical bedrocks on digital simulation.

本文首先介绍了数值模拟技术及回弹发展历史，回顾了国内外学者在这方面的研究，随后介绍一些有关数值模拟的理论基础。

We are still seeing any bounce being sold into which is a feature of downtrends and although we have fallen over $85 dollars in three months we would advise against trying to pick the markets bottom and only enter a long position, for anything longer than a day trade, when the technical picture has shown us a signal of the trends reversing.

我们仍然看见因为有卖出所以有回弹，这正是下跌的特徵。虽然市场在三个月内有超过$85下跌，我们建议可尝试找住底部，建立多头，保持超过一日交易，技术图表显示有反转趋势。短中期趋为为熊市，长期趋势为横向式。

With this model, the deformation and stress distributions of the flange joint are analyzed using ANSYS FEM software, and the influences of gasket properties, tube side pressure and shell side pressure, bolt pr.

本论文以U形管换热器法兰夹管板接头为研究对象，考虑垫片材料压缩的非线性特性和压缩-回弹时的时滞效应，将法兰接头各元件看成一个系统，研究各元件的相互作用，建立了管板-法兰-垫片-螺栓连接系统的非线性三维有限元分析模型。

Resilient calculating method of bending forming die for wing blade is put forward.

提出了机翼形叶片弯曲成型模的回弹计算方法。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。