器

This example focuses on the design seeder platoon of vehicles, fertilization devices, trenching vehicles structure.

本例着重对播种机排种器、排肥器、开沟器、覆土器以及镇压轮等结构进行设计选择。

The present invention discloses a silver iodide acetone solution above-ground combustion equipment, including liquid storage tank, air compressor, liquid-supplying and gas-supplying pipelines, filter, atomizer, pulse high-voltage igniter, combustion chamber and wind-proofing device, the above-mentioned components are placed on a base seat. The liquid storage tank is communicated with liquid inelt of atomizer by means of filter, the air outlet of air compressor is communicated with air inlet of the atomizer, the combustion chamber is a circular truncated cone shaped cylinder body whose upper portion is larger and lower portion is smaller, and is placed on a vertical rod.

本发明公开了一种碘化银丙酮溶液地面燃烧装置，包括储液罐、空气压缩机、供液供气管路、过滤器、雾化器、脉冲高压点火器、燃烧室和防风装置，上述装置均设置在一底座上；其中储液罐通过过滤器连通到雾化器进液口，空气压缩机出气口连通到雾化器进气口；燃烧室为一下大上小的圆台形筒体，设置在一竖杆上，雾化器的出口设置在燃烧室内；燃烧室上外围设置防风装置，该防风装置是一圆形防风圈；所述脉冲高压点火器的一电极设置在燃烧室壁面，另一电极设置在燃烧室内。

At 135 mm depth and 0.28 m/sec speed, the biomimetic furrow opener surface with UHMWPE tubular ridges recorded 0.62 kN and 0.17 kW, while at 135 mm depth and 0.92 m/sec speed, the values were 0.91 kN and 0.82 kW. The experimental values of resistance force and power for the conventional surface furrow opener at 100 mm depth, and 0.28 m/sec speed were 0.72 kN and 0.20 kW, while at 100 mm depth and 0.92 m/sec speed, the values were 1.11 kN and 1.0 kW. At 135 mm depth and 0.28 m/sec speed, the conventional surface furrow opener recorded 0.93 kN and 0.25 kW, while at 135 mm depth and 0.92 m/sec speed, the values were 1.50 kN and 1.35 kW.

试验测试结果：当耕深100 mm和耕作速度0.28 m/sec时，实测的普通开沟器的土壤阻力和动力消耗分别为0.72kN和0.20kW；当耕深100 mm和耕作速度0.92 m/sec时，实测的普通开沟器的土壤阻力和动力消耗分别为1.11kN 和1.0kW；当耕深135 mm和耕作速度0.28 m/sec时，实测的普通开沟器的土壤阻力和动力消耗分别为0.93kN和0.25kW；而当耕深135 mm和耕作速度0.92 m/sec时，实测的普通表面开沟器的土壤阻力和动力消耗分别为1.5kN和1.35kW。

The predicted values of resistance force and power for the conventional surface furrow opener at 100 mm depth and 0.28 m/sec speed were0.51 kN and0.14kW, while at 100 mm depth and 0.92 m/sec the values were0.98kN and0.88kW. At 135 mm depth and 0.28 m/sec speed, the conventional surface furrow opener recorded 0.70 kN and 0.20 kW, while at 135 mm and 0.92 m/sec speed, the values were 1.40 kN and 1.26 kW. The predicted values of resistance force and power for the biomimetic furrow opener surface with UHMWPE tubular section ridges at 100 mm depth and 0.28 m/sec speed were 0.45 kN and 0.12kW, while at 100 mm depth and 0.92 m/sec speed, the values were 0.73kN and 0.66 kW.

对于超高分子量聚乙烯材料仿生脊型非光滑结构表面，当耕深100 mm和耕作速度0.28 m/sec时，预测的仿生开沟器的土壤阻力和动力消耗分别为0.45kN和0.12kW；当耕深100 mm和耕作速度0.92 m/sec时，预测的仿生开沟器的土壤阻力和动力消耗分别为0.73kN和0.66kW；当耕深135 mm和耕作速度0.28 m/sec时，预测的仿生开沟器的土壤阻力和动力消耗分别为0.62kN和0.17kW；而当耕深135 mm和耕作速度0.92 m/sec时，预测的仿生开沟器的土壤阻力和动力消耗分别为0.91kN和0.82kW。

The experimental values of resistance force and power for the biomimetic furrow opener surface with UHMWPE tubular section ridges at 100 mm depth and 0.28 m/sec speed were 0.60 kN and 0.16 kW, while at 100 mm depth and 0.92 m/sec speed, the values were 0.80 kN and 0.72 kW. At 135 mm depth and 0.28 m/sec speed, the biomimetic furrow opener surface with UHMWPE tubular section ridges recorded 0.76 kN and 0.21 kW, while at 135 mm depth and 0.92 m/sec speed, the values were 0.95 kN and 0.85 kW. The predicted and experimental values of resistance force and power for the conventional surface furrow opener were higher than predicted and experimental values for the biomimetic furrow opener surface with UHMWPE tubular section ridges.

对于超高分子量聚乙烯材料仿生脊型非光滑结构表面，当耕深100 mm和耕作速度0.28 m/sec时，实测的仿生开沟器的土壤阻力和动力消耗分别为0.6kN和0.16kW；当耕深100 mm和耕作速度0.92 m/sec时，实测的仿生开沟器的土壤阻力和动力消耗分别为0.8kN和0.72kW；当耕深135 mm和耕作速度0.28 m/sec时，实测的仿生开沟器的土壤阻力和动力消耗分别为0.76kN和0.21kW；而当耕深135 mm和耕作速度0.92 m/sec时，实测的仿生开沟器的土壤阻力和动力消耗分别为0.95kN和0.85kW。

Foot of the ON | OFF switch, online ON | OFF switch, pipe tuning, sub-light ON | OFF mother paragraph without fine-tuning of light dimmers, touch-free fine-tuning dimmers paragraph (a lamp ON | OFF mother lights without paragraph fine-tuning), the pedal dimmers (son of lights ON | OFF home without lights above fine-tuning), the pedal dimmers .......

脚踏的ON|OFF开关、线上ON|OFF开关、管内微调、子灯ON|OFF 母灯无段微调的调光器、触摸无段微调调光器（子灯ON|OFF 母灯无段微调）、脚踏的调光器（子灯ON|OFF 母灯无段微调）、脚踏的调光器……。

Unfortunately, there is inevitably difference in characteristics of the induction motors and converters in a parallel AC drive system, therefore each induction motor as well as converter can not operate at the same working point, some may be overload, some underload.

并联着的各个交流调速系统的负载是不均衡的，这是因为逆变器所带的负载—异步电动机参数及特性不可避免地存在差异，两或多台逆变器作为电源，其等效参数也很难一致，各驱动轮径总存在偏差，因此各台逆变器的输出电流和各台异步电动机的定子电流是不相一致的，有的逆变器、异步电动机可能过载，有的还可能欠载。

Studied the solid particles cyclone separation under structural parameters and operating parameters of different hydrocyclone, the results showed that major factor influence split ratio is in the ratio of entrance to exit pressure of hydrocyclone. Exit pressure has a certain influence on the split ratio, the various of the diameter and cone angle of hydrocyclone (in the ratio of entrance to exit pressure is constant) have no influence on split ratio; With diameter and cone angle increase, the separation granularity gradually increasing and recovery ratio decreasing; With entrance pressure increase, the separation granularity of hydrocyclone decrease, the split ratio of underset will increase slowly; With the diameter of overflow pipe increase, the separation granularity of hydrocyclone increasing and recovery ratio decreasing; With the diameter of underset pipe increasing, the separation granularity of hydrocyclone decreasing and recovery ratio increasing.

在不同的水力旋流器结构参数和操作参数下，对固体颗粒的旋流分离进行了分析研究，结果表明：旋流器的排出口比是影响分流比的主要因素，进口压力对分流比有一定影响，水力旋流器的直径变化和锥段角度变化对分流比基本上没有影响；随着直径、锥段角度的增大，分离粒度逐渐增大，回收率降低；随着入口压力增大，水力旋流器的分离粒度变小，底流的分流比会缓慢增加；随着溢流管管径的增加，分离粒度增大，分流比明显减小，回收率降低；随着底流管直径的增加，分离粒度减小，分级效果明显下降，回收率会增加。

Mould slag entrapment brings out the phenomenon of break wire in the drawing of high-purity steel C72DA.Through studying mould flow field,conclusion is considered that mould slag entrapment is near the mould wall and is caused by serious undulation of the steel level,the hot metal bias or unmelted mould power.

结晶器卷渣引起高纯净度的C72DA钢在拉拔过程中出现断丝现象，通过对结晶器流场的研究，认为结晶器卷渣主要在结晶器壁附近，是由于表面钢水的波动严重、钢水偏流、或保护渣熔化不良引起的。

The hardware system comprises a football locating emitter, a site corner orientation emitter, a vidicon, a radar velometer, a player locating emitter and a site vibration receptor. The software system comprises a plenty of computer program software developed for aiming at the hardware.

其中硬件系统由足球定位发射器、场地边角定向发射器、摄像机、雷达测速器、球员定位发射器及场上裁判振动接收器等组成；软件系统则由针对以上所述硬件进行开发的各种电脑程序软件等构件组成。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。