喷射管

The influence of several parameters including injection rate of nozzle exit, the ratio of length between nozzle and inner gular tube, the ratio of length between gular tube and it's inner diameter and back pressure on the performance of gas solid injector is analyzed.

分析了喷嘴出口射流速度、喉嘴距、混合管段尺寸及背压等参数对气固喷射器性能的影响，结果表明：存在最佳的喷嘴出口射流速度、喉嘴距以及喉管长与其内径之比使得固气比达到最大值；而背压的增加则不利于提高喷射器性

The interactions between gas and particles were considered by a two-way coupling method.The motion of particles in the spouted bed with complex geometry was solved by combining DEM and boundary element method.The minimal spoute...

通过采用BEM+DEM-CFD相结合的方法进行模拟计算，得到了喷动床的最小喷动速度，研究了不同表观气速下床内的流型，得到了二维导流管喷动床的床层压降与表观气速的关系，统计分析了喷射区、环隙区内颗粒的运动速度和相应的空隙率，全面地描述了二维导流管喷动床内的气固流动特征。

Designing and founding the thermoacoustic test-bed. The structure and dimension of condenser, heater, ejector, regenerator, sound room, feedback loop, resonance forthright and pulse tube refrigerator are showed detailed.

设计并搭建了热声驱动的脉管制冷系统试验台，对系统中的冷却器、加热器、喷射泵、回热器、声容、反馈回路、谐振直路及脉管制冷机等的结构尺寸做了详细介绍。

Professional production and sale of "a relaxation" brand various types of cloth hose, the main varieties: cloth pipes, air pipes, pipelines, transmission of acid-base tubes, steam pipes, pipe sand blasting, cement injection tube, lose food pipe, Oil hot food pipe, bridge hole system pipes, to attract pipe, oil heat pipe.

专业生产，销售"创驰"牌各类夹布胶管，主要品种：夹布输水管，空气管，输油管，输酸碱管，蒸汽管，喷砂管，水泥喷射管，输食品管，油热食品管，桥梁制孔管，吸引管，耐油热管。

A kind of new typer mixing reacter with an injection tube and a baffled chamber for producing calcium superphosphate was introduced.

介绍了由一个喷射管和一个折流室构成的用于普钙生产的新型混合反应器。

In this paper,a new type of mixing reaction unit composed of injector and baffled chamber,which is used in production of calcium superphosphate

介绍了由一个喷射管和一个折流室构成的用于普钙生产的新型混合反应装置，它有结构简单、节能、操作方便、质轻体小、成本低、应用效果好等优点。

In addition, as the secondary steam get in direct contact with the ejection flow to carry out heat exchange, most steam is condensed into water, while the uncondensed small minority steam and the uncondensed gas will also get into friction, with the high speed water ejection, mixed and extruded, then discharged through diffusing pipe, thus to form up higher vacuum inside.

另外由于二次蒸汽与喷射水流直接接触，进行热交换，绝大部分的蒸汽凝结成水，小量未被冷凝的蒸汽与不凝结的气体亦由于与高速喷射水流互相摩擦，混合挤压，通过扩压管被排除，使器室内形成更高的真空。

Professional production and sale of "a relaxation" brand various types of cloth hose, the main varieties: cloth pipes, air pipes, pipelines, transmission of acid-base tubes, steam pipes, pipe sand blasting, cement injection tube, lose food pipe, Oil hot food pipe, bridge hole system pipes, to attract pipe, oil heat pipe.

专业生产，销售&创驰&牌各类夹布胶管，主要品种：夹布输水管，空气管，输油管，输酸碱管，蒸汽管，喷砂管，水泥喷射管，输食品管，油热食品管，桥梁制孔管，吸引管，耐油热管。

Key introduces the CT-121 bubble type spraying tower haze desulphurization craftCT-121 uses the limestone - gypsum (it is in the present world is maturest, most economical, applies broadest desulphurization craft) the aqueous method desulphurization craftIt the sulphur dioxide absorption, the oxidation, neutral, technological processes and so on crystallization as well as dust removal merges to an independent gas - fluid - solid phase reactor in carries onIt the sulphur dioxide absorption, the oxidation, neutral, technological processes and so on crystallization as well as dust removal merges to an independent gas - fluid - solid phase reactor in carries on

与传统的石灰石-石膏湿法烟气脱硫工艺相比，CT-121最大的特点在于鼓泡式吸收塔。它将二氧化硫的吸收、氧化、中和、结晶以及除尘等工艺过程合并到一个单独的气-液-固相反应器中进行。气体进入喷射管，喷射成无数小气泡，形成鼓泡区，从而大大增加了传质面积，提高了脱硫效率。CT-121脱硫工艺能够达到95%以上稳定连续的脱硫率，最低10 以下的粉尘排放率以及优异的可靠性和实用性。问题补充：谁再帮忙给篇，石灰石-石膏湿法烟气脱硫方面的论文文献，谢谢了中英文版的，谢谢了555

2 The provisions of valve flap stent thrust nut in space; 4.3 will bring more than ejector stem components, and into the valve flap bracket, now can adjust screw ring on the injector; adjustment ring discharge pipe may be twisted too high in case of this case, when the valve assembly after the valve flap in contact with its seat before the valve flap seat will have an additional load on the adjustment ring edge, in order to avoid this from happening, should enable the adjustment ring hole just below the injector thread, through which holes should not be able to see thread.

4.2 规定阀瓣支架与止推螺母中的间隙； 4.3 将喷射器提起超过阀杆组件，并放到阀瓣支架上，现在可以把调节环拧在喷射器上；调节环可能在排放管上拧得太高，如遇此情况，当阀门组装后，在阀瓣与其座相接触前，阀瓣座将加载荷于调节环的边上，为了避免此情况的发生，应使调节环上的孔正好低于喷射器的螺纹，通过这些孔应不能看到螺纹。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐