喷射口

The purpose of the invetion is to effectively stop the blowoff of an injected fuel into an exhaust port when the opening and closing of valves are overlapped with each other by properly setting the fuel injection direction of a fuel injection device mounted so as to face the intake passage of an internal combustion engine.

提供一种内燃机的进气结构，适当设定被安装成对着内燃机的进气通道的燃料喷射装置的燃料喷射方向，有效防止在气门开闭动作时间的重合期间朝向排气口的喷射燃料的喷泄。

A piston-shaped valve needle is contained in the bore in a longitudinally sliding fashion and has an essentially conical valve sealing surface by means of which the valve needle cooperates with the valve seat in order to control the at least one injection opening.

一个活塞状的阀针(5)可纵向移动地设置在孔(3)中并具有一个基本上锥形的阀密封面(7)，阀针(5)通过该阀密封面与阀座(9)相配合，以控制至少一个喷射口(11)。

The distributor plate at the bottom of the column. A constant high flow rate and head of water in the column and at the eductor inlet is maintained by circulating it through a pump and storage tank, in a closed loop.

用内环流中的泵和储水罐中的循环水来维持气馏柱和喷射口部分恒定的高速水流。

The results show that the discharge and cooling stages of sparkjet were simulated by computational method. The instance energy input can produce the condition of high pressure and temperature in the actuator, which induce the forming of synthetic jet. With the increment of the input energy, the velocity of the synthetic jet could be increased to the supersonic state. Under the periodic energy input, the distribution of the sparkjet velocity on the nozzle is non-sinusoidal. And the discharge velocity of jet is much larger than the suction velocity of the flow from environment.

计算结果表明：采用本文的计算方法可以模拟出火花型激励器喷射、吸入的工作阶段；电火花瞬间能量的输入产生了腔体内的高温、高压环境，从而诱发合成射流的形成；当激励能量增加，激励器产生的合成射流速度增加，可达到超声速状态；周期性激励下，火花型合成喷喷口处的轴向平均速度随时间不是正弦分布，且喷射过程的最大速度要远远大于吸收过程的最大速度。

In order to increase the efficiency, pumps were improved, eject pump had two inlets, each was located on one side of pump, and the inlet of centrifugal pump was used as one Enteromorpha prolifera inlet.

为了进一步提高装置的工作效率，在原有设备的基础上，对离心泵和喷射泵均进行改进，喷射泵改为双吸口，位于泵体两侧，同时离心泵的入水口也作为浒苔吸口使用，并给出喷射泵主要设计参数。

These results clearly justifies that in combustor, the injector location and its conditions have no effect on the flowfield structure but have strong effect on the combustion efficiency, and that inside the engine, undesirable injector conditions can result in the engine thermal choked and unstart.

第五章计算了含横向喷流的二维燃烧室和一种简化一体化超燃冲压发动机流场，发现在燃烧室中喷口位置及喷射条件对流场的结构影响不大，但对燃烧效率却有较大的影响；而在发动机内部，不适当的喷射条件，有可能引起发动机的&热壅塞&，使发动机无法启动。

In the gas technique, two gas burners are placed so that both the front and back of the cloth is singed in a single pass through the equipment. The hot cloth is then passed through water or steam to extinguish any sparks that may be present.

在气体烧毛工艺中，在织物的正面和反面各有一套火焰喷射口，在织物通过时，其正面和反面会同时受到灼烧，温度较高的织物通过水或蒸汽以便熄灭可能出现的火星。

In the gas technique, two gas burner s are placed so that both the front and back of the cloth is singed in a single pass through the equipment. The hot cloth is then passed through water or steam to extinguish any sparks that may be present.

在气体烧毛工艺中，在织物的正面和反面各有一套火焰喷射口，在织物通过时，其正面和反面会同时受到灼烧，温度较高的织物通过水或蒸汽以便熄灭可能出现的火星。

Mitsubishi increased the combustion efficiency by optimizing the design of the cylinder head intake and exhaust ports, by incorporating the MIVEC system on both intake and exhaust valves and by using injectors that give an ultra micro droplet fuel spray.

三菱增加通过优化的气缸盖进气口和排气口设计的燃烧效率，通过搭载两进排气门用喷射器，让人们可以超微小滴燃油喷射和的MIVEC系统。

The influences of the nozzle diameter, pre-expansion pressure and pre-expansion temperature on the residence time, diameter, number, velocity and temperature of particles have been investigated.

研究了喷射口直径、预膨胀压力、预膨胀温度对颗粒停留时间、粒径分布、颗粒数量、颗粒速度及颗粒温度的影响。

I am accused of being overreligious," she said in her quiet, frank manner,"but that does not prevent me thinking the children very cruel who obstinately commit such suicide.""

客人们在卡罗利娜·埃凯家里，举止就文雅一些，因为卡罗利娜的母亲治家很严厉。

Designed by French fashion house Herm è s, this elegant uniform was manufactured in our home, Hong Kong, and was the first without a hat.

由著名品牌 Herm è s 设计，这件高贵的制服是香港本土制造，是我们第一套不配帽子的制服。