喷射

At present, with the automotive and electronic industrial technology of rapid development, the use of the car getting higher and higher performance requirements, the electronically controlled fuel injection technology in the car on a wide range of applications, to reduce fuel consumption and reduce environmental pollution requirements of the increasingly strong electronic fuel injection system to replace the traditional carburetor is a foregone conclusion, for the fittings to meet the needs of the market in June 2003 the company started to develop my EFI system with some fittings and matching engine plant, while the introduction of Marelli, Delphi, Motorola, United Electronics, Mitsubishi Electronic Fuel Injection System complete set of fittings (for: Jinbei, ruichi,ó, the Great Wall pickup, Chinese, Zun Chi, Chun-Jie, Haversian, Seyfert, Chery, Tiggo, ZTE, Tai Di , dawn, landscape sea lions, the South East Series EFI models fittings and so on) the rapid sales network covering the domestic market fittings.

目前，随着汽车及电子工业技术的高速发展，对汽车的使用性能要求越来越高，电子控制燃油喷射技术在汽车上的广泛应用，对降低汽车耗油量和减少环境污染的要求日趋强烈，以电子燃油喷射系统取代传统的化油器已成定局，为满足配件市场的需求2003年6月我公司开始研制电喷系统配件并与部分发动机厂配套，同时引进马瑞利、德尔福、摩托罗拉、联合电子、三菱全套电喷系统配件（适用：金杯海狮、锐驰、阁瑞斯、长城皮卡、中华、尊驰、骏捷、哈弗、赛弗、奇瑞、瑞虎、中兴、大迪、曙光、风景海狮、东南系列等车型的电喷配件）销售网络迅速覆盖了国内配件市场。

On the base of the brief description of the drive and control system of micro-fluid and the experimental setting of the technology of micro-injection, a novel process of the hydrophobe treating used to mend the characteristic of the inner and outer surface on micro-pipette is designed, which can improve greatly the injected effect and eliminate the disadvantage such as seepage or regurgitation during injection. The author puts forward the way of measuring the inside diameter of the micropipette. The program of measuring micro injection amount is designed. The original data of the micro injection experiment are explained and interpreted at last in the thesis.

在简要描述微流体驱动控制系统和微注射技术实验条件的基础上，设计了改善微针内外表面特性的疏水化处理工艺，消除了微喷射过程中的渗流、回流现象，改善了微注射过程中的流动特性，提高了微注射效果，得到了数字化微喷射的实验结果；提出了精确测量微针内径的折射率法；设计了纳升级以下的微液滴量的检测方案；最后，论文对微注射技术实验中的原始数据进行了分析。

Analysed angle of trajectory height, eject and fuel injection arteries and veins wide reach oily film to oily film area the influence of the biggest ply, got parameter falls mensurably differring most lard film ply and oily film area.

分析了喷射高度、喷射角度及喷油脉宽对油膜面积及油膜最大厚度的影响，定量地得到了不同参数下的最大油膜厚度和油膜面积。

Multi-cylinder engines are normally equipped with pumps in unit monobloc form incorporating a corresponding number of elements,having a common camshaft and control means but provided with individual adjustments for regulating their output and setting their timing .

多汽缸发动机一般情况下装配整体式油泵，把相关的喷射单元组合成一体，共用凸轮轴和控制方式，但可单独调整以调节各自功率输出和设定各自的正时。每个喷射单元必须输送等量燃油，按照预定的输送比率分别校准。

They are associated with stenosis of either the aortic or the pulmonic valve, with hypertension or dilatation of either the aorta or the pulmonary artery or both.

喷射性喀喇音喷射性喀喇音音调高，出现于收缩早期，与主动脉瓣或肺动脉瓣狭窄有关，也与主动脉瓣或肺动脉瓣或两者的高血压或膨胀有关。

The present technique provides the spray device with an atomizing spray section and a releasable mount.

本技术所提供的喷射装置有一雾化喷射部分和一个可松脱的安装件。

Accordingly, the spray device or its substitute may be remounted to the releasable mount in the desired spray position.

因此，本喷射装置或其替代物可以重新安装到可松脱安装件上的所需喷射位置处。

In addition, the releasable mount may be mounted releasably to the spray device, such that the releasable mount may remain attached to the mounting member in a desired spray position.

此外，可松脱安装件可以可松脱安装在喷射装置上，这样，所述可松脱安装件就能保持在所需喷射位置处固定在安装部件上。

In addition, as the secondary steam get in direct contact with the ejection flow to carry out heat exchange, most steam is condensed into water, while the uncondensed small minority steam and the uncondensed gas will also get into friction, with the high speed water ejection, mixed and extruded, then discharged through diffusing pipe, thus to form up higher vacuum inside.

另外由于二次蒸汽与喷射水流直接接触，进行热交换，绝大部分的蒸汽凝结成水，小量未被冷凝的蒸汽与不凝结的气体亦由于与高速喷射水流互相摩擦，混合挤压，通过扩压管被排除，使器室内形成更高的真空。

These results clearly justifies that in combustor, the injector location and its conditions have no effect on the flowfield structure but have strong effect on the combustion efficiency, and that inside the engine, undesirable injector conditions can result in the engine thermal choked and unstart.

第五章计算了含横向喷流的二维燃烧室和一种简化一体化超燃冲压发动机流场，发现在燃烧室中喷口位置及喷射条件对流场的结构影响不大，但对燃烧效率却有较大的影响；而在发动机内部，不适当的喷射条件，有可能引起发动机的&热壅塞&，使发动机无法启动。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。