喷出的

Based on statistical results and the volcanic lithology and facies map, high cracks surface pore concentrates at diatreme subfacies and cryptoexploisve sub-facies of volcanic conduit facies, inner subfacies of extrusive facies, pyroclastic flow subfacies and base surge subfacies of explosive facies, lower subfacies of effusive facies which are close to the volcanic edifices center. Holes surface pore focus on upper and middle subfacies of effusive facies which locates in the edifice slope.

将物性结果结合平面岩性岩相图，确定出裂缝面孔率高的区域主要集中在火山机构中心附近的火山通道相火山颈亚相和隐爆角砾岩亚相、侵出相内带亚相、爆发相热碎屑流和热基浪亚相、喷溢相下部亚相；气孔面孔率高的区域集中在距离火山口较近的斜坡处，亚相主要为喷溢相上部、中部亚相。

Based on the theory of large eddy simulation and the method of VOF , the initial breakup process of fuel liquid jet, which eject from the nozzle exit at the time scale of micro-second level, is investigated. The mechanism of primary atomization is analyzed, and the initial breakup model of liquid jet is presented. By modeling and numerical simulation of atomization for a diesel nozzle under the given conditions, the initial umbrella-like spray shapes are obtained, which fits better with the experimental results. Meanwhile, the droplets secondary breakup process, such as leeward RT breakup, dumbbell-like breakup and droplets coalescence, etc. are exhibited visually.

基于大涡模拟LES理论和VOF方法，考察了燃油喷雾初始时刻即时间尺度为微秒级的液柱破碎过程，分析了初始破碎的机理，给出了该时间尺度下液柱初始破碎过程的模型；通过对一特定条件下的柴油机喷油器的建模和喷雾过程的大涡数值模拟，获得了液柱初始时刻"伞状头部"的喷雾形态，所得计算结果与相应的试验数据符合较好；数值模拟还直观地展现了液滴背风RT破碎、哑铃型破碎以及液滴的聚集融合等液滴的二次雾化过程。

Intelligent automatic adjustment of the whole, powerful, advanced software technology with the world's topúcomparable, some functionality has exceeded foreign advanced level, completely changed theúChinese low-cost low-quality image, for Condit Coding machine go out of the country, Yang Wei of China, the World Service Swinger technical obstacles.

全智能自动调节，功能强大，先进的软件技术可与世界顶极喷码机相媲美，部分功能已超过国外先进水平，彻底改变了中国喷码机低质低价的形象，为康迪喷码机走出国门、扬我国威、服务世界扫平了技术障碍。

Other cause can be vibrations of the print head letting small air bobbles inside the print head preventing the ink head of firing one ore more nozzles, also change of cartridges can let a little bit of air inside the ink system, in case of missing nozzles it will look like white line within the print, then push the pump bottom for a few seconds, please have a JetMaster tissue in front of the head when using the pump, otherwise you are facing ink all over your machine, the ink can spray more than one meter out of the print head using this function, so please use it carefully.

喷印头的振动释放的小茸球在喷印头中阻塞喷头的一个或多个喷嘴的射击，同时和的变化会使一点空气进入油墨系统，避免喷嘴的缺失。然而当喷嘴丢失时，喷印看起来像白线，这时推动操作泵底部数秒。请在顶端前有Jet Master棉纸时，使用操作泵，否则油墨会溅到机器上，可溅出喷印头1米多。因此，请谨慎使用。

Aiming at the problems that oil pressure of existing P7100 type fuel injection pump can not meet the demand of the injection pipe fatigue test, on the basis of analysis and calculation, we designed a set of hydraulic integrated supercharging device.

针对现有 P7100型喷油泵出油压力不能满足喷油管疲劳性试验要求的问题，在分析、计算的基础上，设计出一套全液压集成式双作用增压装置；对其工作原理、结构特点进行了简要介绍，提出了系统集成化的设计思想，实现了各缸、阀、油路等元件的集成化。

The mainly conclusions in our research are as flowing: tungsten trioxide powders with 100 nm primary particle are obtained by spray drying,calcination and wet milling process, and an average size of quadric particle composed of agglomerated particles is 0.64 μm; tungtsen powders with 39 nm grain size and 60 -100 nm primary particle are produced directly from previous tungsten trioxide using one step reduction in hydrogen at 700℃, and an average size of quadric particle of tungsten powder is 2.91 μm; tungsten trioxide and copper tungstate compound powders with 100 nm - 200 nm primary particle are produced using ammonia metatungsten and copper nitrate as raw materials by spray drying,calcination and wet milling process;the compound powders are transformed completely into tungsten and copper compound powders by reduction in hydrogen at 700℃,in which tungsten grain size is 59 nm and copper grain size is 51 nm; primary particle size of compound powders is 80 - 120 nm,and an average size of agglomerated quadric particle is 1.86 μm; tungsten nitride powders with 35 nm grain size are prepared from tungsten trioxide powders by nitrogen treatment thoroughly in pure ammonia at 650℃, and an average size of agglomerated quadric particle is 0.64 μm in normal temperature.

研究结果表明：采用喷雾干燥—焙烧—球磨工艺可以制备出粒度约为100nm的WO_3粉体，它们在团聚后形成的二次颗粒平均粒度为0.64μm；采用一步直接氢还原方法可在700℃下从上述WO_3粉体制备出晶粒尺寸为39nm的、一次颗粒粒度为60-100nm的W粉体，其二次颗粒的平均粒度为2.91μm；以偏钨酸铵、硝酸铜为原料，采用喷雾干燥—焙烧—球磨工艺可制备出一次粒度为100-200nm的WO_3和CuWO_4混合粉体；采用氢还原工艺可在700℃下将这种粉体完全转变为W、Cu复合粉体，其中W的平均晶粒粒尺寸为59nm，Cu的平均晶粒尺寸为51nm；复合粉体的一次颗粒尺寸为80-120nm，在常温下团聚后形成的二次平均粒度为1.86μm；采用纯氨氮化工艺可以在650℃下由WO_3粉体制得WN，其晶粒尺度为35nm，在常温下团聚后的二次平均粒度为6.4μm。

The paper analyzes the fuel injection control strategy and provides the calculation method of engi- neer load and injection measuring width.The correcting reasons,calculation method and effect of many cor- rections are also given.

主要对电子燃油喷射系统喷油控制进行分析，详细给出了发动机负荷、喷油脉宽的计算方法，同时也给出了各修正量的修正原因、计算方法和影响效果。

To burning the heavy oil in diesel locomotive, the injection unit must be adjusted, such as the clearance of piston, the spring character of unilateralism valve, the needle valve lift of injector and so on. At the same time, the parameter of injection, such as the injection advace angle, the injection time, should be adjusted according to the actual instance.

针对燃用重柴油的实际，需对柴油机喷射元件，如：喷油泵柱塞偶件间隙、出油阀弹簧刚度、喷油器针阀升程、及喷射参数，如：喷油提前角、喷油定时等均需作出调整，本文论述了具体的调整方法和依据。

Therefore, by comparing particle distribution of the spraying under different water pressure, and the nozzle's outlet velocity simulation get by Ansys, which is a software for mechanical simulation, a proposal of the application of 1.5mm nozzle, 8Mpa water pressure on the spot was put forward.

在比较多种光学测粒仪的基础上，选择Winner313系统测量不同孔径喷嘴在不同供水压力下喷雾雾场的粒径分布。通过分析比较喷嘴在不同压力下喷雾雾场的粒径分布和Ansys模拟得到的喷嘴内部及出水口速度场，建议现场应用1.5mm喷嘴、供水压力为8MPa进行喷雾。

Under spraying humidification state, the parameters of JYPW-1 spraying axial fans for textile enterprises such as flow, total pressure, efficiency, shaft power and acoustic power level changing with water-air ratio were tested, and the performance parameter curve changing with water-air ratio was obtained. The approximate formula of its pneumatic performance in different water-air ratio condition were deduced which can be referenced for of selection and project application.

在喷雾加湿工况下，对纺织空调系统所用的JYPW-1型喷雾轴流通风机的流量、全压、全压效率、轴功率和比A声级噪声等性能参数随喷淋水气比的变化进行了测试，得到了喷雾风机性能参数随水气比变化的曲线，并整理出喷雾风机在不同水气比时，其气动性能的近似计算公式，可供喷雾风机选型和工程应用时参考。

Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.

Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。

I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.

我来只是现在，'歼灭战perfuming自己与胡努特，那麼，他来到和SAT 。