唇的

The area where the changes is much bigger during the anterior part of the mandibule and maxilla is the upper and lower clypeus and the vermilion of which the tissue is relax, packing and the unit tissue area was compressed smaller in some place.

上下颌前份截骨术后发生较大形变的上下唇基部及唇红，这些部位组织松弛、堆积、某些部位单元组织面积压缩变小。

Since the WV Packing is a multiple lip hydraulic seal, it is recommended over a single lip seal for applications where side loading is a factor.

由于西弗吉尼亚州是一个多包装液压密封唇，建议在一个单一的应用唇密封在侧负荷是一个因素。

Corolla yellow, with red galea and white margin on lower lip; lower lip to 3 cm wide

花冠黄，具红色和白色由下唇开出的边缘；下唇到3厘米宽 334 Pedicularis tricolor 三色马先蒿

Lateral 2 staminodes of outer whorl petaloid, or forming small teeth at base of labellum, or adnate to labellum, or absent.

外轮的侧面的2个退化雄蕊花瓣状，或者在唇瓣基部形成小齿，或者与唇瓣贴生，或者无。

And direct grain lip secured your labial form namely, also got on color lines at the same time.

而直接纹唇呢就是把你的唇形固定了，同时也把颜色纹上了。

The double pedicle arc-shaped flap nympholepsy is an ideal method for its well healing,no visible scar,normal sensation,and good final shape.

弧形双蒂瓣小阴唇整形术具有术后伤口愈合良好，瘢痕隐蔽不明显，感觉正常，外阴形态佳等优点，是治疗小阴唇肥大的较理想方法。

All of them were satisfied with vulvae shape.Conclusion The double pedicle arc-shaped flap nympholepsy is an ideal method for its well healing,no visible scar,normal sensation,and good final shape.

弧形双蒂瓣小阴唇整形术具有术后伤口愈合良好，瘢痕隐蔽不明显，感觉正常，外阴形态佳等优点，是治疗小阴唇肥大的较理想方法。

Apply suitable amount of powder throughout the puff or brush and massage lightly on the face.

选择适合当日彩妆和服装的唇膏色彩，直接涂于唇上或用唇刷涂抹。

Try over clear or nude gloss for a sexy, shimmery look.

尝试添加在透明或裸唇色唇蜜上可制造性感，晶莹剔透的妆容。

Furthermore, three species of Sinocrossocheilus were described respectively as S. labiata, S. nigrovittata and S. longibulla. Zoogeography and Diversity of Sinocrossocheilus genus were discussed also.

就我国特有属华缨鱼属的分类进行系统整理，描述了华缨鱼属4新种-宽唇华缨鱼、粗唇华缨鱼、黑带华缨鱼和长鳔华缨鱼，并在动物地理学和进化生态学方面初步研究了华缨鱼属鱼类。4。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。