响应面

Presents the design of longitudinal control for ASTOVL lift-fan aircraft, a multi-variable, strong-coupling, complicated nonlinear system to make the system nonlinear offset and decouple, and the method used for linear system in designing the system to gain expectant flying qualities and the combination of aerodynamic control surfaces with thrust vectors to delay the control surfaces getting into saturation, and the minimum N-norm generalized inverse theorem of weighted generalized inverse adopted to apportion the moments commands, which make the control surfaces gain appropriate deflection and the simulation results to verify the dynamic inverse control laws designed really make the system nonlinear offset and decouple; when one command is given, only this output will response, and others do not response; when all commands are given together, the responses will be just the linear superpose of the response of each command, therefore the operation of the pilot will be simplified greatly.

摘 要： ASTOVL升力风扇飞机是多变量、强耦合、复杂的非线性系统，采用非线性动态逆理论设计控制律以实现系统的非线性对消及解耦，然后，采用线性系统的设计方法对系统进行设计，以使系统获得期望的飞行品质。同时，考虑到ASTOVL升力风扇飞机是由气动舵面和推力矢量融合作用的，为了延缓各舵面进入饱和的时间，采用加权广义逆中的极小N-范数广义逆定理分配力矩指令，从而使各舵面达到适当的偏转角。并将所设计的控制律进行了仿真，结果验证了所设计的动态逆控制律使系统实现了非线性对消和解耦，单个指令作用时，只有该项响应，其余不受影响；所有指令作用时，其结果就等于单个指令作用时的线性叠加，这样使驾驶员的操纵大大简化而易于控制，从而大大降低了飞行事故率。

So a method that combining the model experiment and numerical computation are discussed in this paper. The flow-induced vibration response of the plane recumbent gate in ShangHai qingshui river is computed in this method, and the result is reasonable and credibility, this method can be extend to compute the other hydraulic structures like overfall dam, guide wall, gate pier and so on, which is under fluctuating pressure.

由此探讨了一种将水力模型试验跟数值计算相结合来计算闸门流激响应具体值的方法，并应用于上海清水河泵闸水下卧倒门的流激响应计算上，结果合理可靠，该方法可以推广应用于溢流坝面、导墙、闸墩等受水流脉动荷载作用的其它水工建筑物。

A correlation of the experimentaldynamic response of the vessels with the theoretical finite element calculations ispresented and discussed.1 The response of the end caps is dominated by transverseand torsional deformation of the plates.The membrane strain is negligible compareto the lateral strain.2 In the lengthwise direction of the inner cylinder,themembrane strain has the same magnitude as that of the bending strain. But for theouter cylinder,the former is much smaller than the later at the same direction.3 Forboth the inner shell and the outer shell,hoop strains are primarily due to themembrane deformation.The amplitude of the circumferential flexural strain isconsiderably small.4 Peak strains in the vicinity of the connection portion of theend caps and the shells are very high.This is important to assess the safety of thecontainer in case of repeated use or tests.5 The applying load to the end cap isdifferent from that to the inner shell plate, but peak stains and nodal displacementsof these two structural parts are nearly the same.It can be inferred that the dynamicresponse of the end cap is greatly affected by the structural vibration excited by theimpulsive loading.

结果表明：1在本文所考虑的载荷水平下，平板变形以板的横向弯曲和扭曲为主，中面应变幅值比较小。2对于内容器，其纵向变形中弯曲应变和中面应变大小接近；而对于外容器，其纵向变形以弯曲为主，中面变形比较小。3内、外壳体的环向变形主要是中面应变，弯曲应变分量很小。4平板和壳体连接处应变很大，这对于多次使用或实验时评价结构安全有指导意义。5尽管内筒底板和大封头上的作用载荷有一定差别，但应变峰值和节点位移峰值基本相近，这说明脉冲载荷激发起来的结构振动对封头的动态响应有很大影响。

The calculation results indicate that the first order metho...

计算结果表明，基于响应面法的一次二阶矩法具有较好的计算精度。

The culture medium was optimized by response surface method as follows: oat flour 32.0 g/L, glycerol 66.9 g/L, soybean meal 29.0 g/L, and ZnSO4

采用响应面方法对培养基进行优化，得到最佳的培养基组成为：燕麦粉32.0 g/L、甘油66.9 g/L、黄豆粉29.0 g/L、ZnSO4

Potato flour, soybean powder, FeSO_4 were screened out as the most suitable carbon source, nitrogen source and inorganic salt source, respectively. Based on these, screening methodology Plackett-Burman design was used to evaluate the effects of twelve factors related to amylase production and three statistically significant factors soybean powder, temperature, bran were selected.

酶对底物的作用方式表现出多样性，以表面扩散侵蚀的方式作用于马铃薯和木薯生淀粉，以表面扩散侵蚀和形成大侵蚀孔洞的方式同时作用于红薯淀粉。4、利用响应面法对菌株AF-1固态发酵产生淀粉酶的条件进行了优化。

A robust mathematical design model based on the response surface method was established for steering trapezoid mechanism. In the model, movement precision during steering course was chosen as the objective function; kingpins distance, axles distance, trapezoid mechanism's bottom angle and steering arm length were defined as the design variables; minimum transmission angle and maximum angle error were considered as the restraint condition.

对于转向梯形机构，以转向过程的运动精度为目标函数，以主销中心距、轴距、转向梯形底角和转向梯形臂长度四个参数作为设计变量，以最小传动角及最大角度误差作为约束，建立了基于响应面方法的稳健设计数学模型。

An equal cross-section blade was investigated and a finite element model was built parametrically. Geometrical parameters (such as length, width and thickness), material parameters (such as young's modulus and density) and speed of blade were considered as input random variables while the static frequencies and dynamic frequencies were output random variables. Combining the finite element method, response surface method and Monte Carlo method, the statistical properties and cumulative distribution functions of static frequencies and dynamic frequencies were obtained. Probability sensitivities analysis, which combined the slope of the gradient and the width of the scatter range of the random input variables, was applied to quantitatively evaluate the sensitivities of static frequencies and dynamic frequencies with respect to the random variables. The Scatter plots of structural responses with respect to the random input variables were illustrated how to adjust the values of the static frequencies and dynamic frequencies by changing input random variables.

文中以某试验台用汽轮机等直叶片为研究对象，考虑几何参数、材料参数和转速的随机性，通过有限元参数化建模，将确定性有限元方法、响应面方法和Monte-Carlo模拟法相结合，从而获得了叶片静频、动频的统计特性和累积分布函数；同时考虑随机变量的梯度和离散范围对静、动频的影响，通过概率敏感性分析，定量地判断出叶片静、动频对随机输入变量的敏感性；通过绘制叶片静、动频与输入变量的散点图，定量地分析了如何改变随机变量以调整静、动频率的方法。

The optimal conditions for the maximal Ps were: glucose 23.75 g/L, phosphate buffer 0.159 M and vitamin solution 13.3 ml/L.

Plackett-Burman设计法和响应面分析法是20世纪中后叶发展起来的优化试验条件统计学方法

Response surface methodology was introduced into the cross sectional optimization of truss, in which the stress and displacement constraints were expressed as linear functions dependent on the reciprocals of cross sections.

把响应面方法引入桁架截面优化中，将应力和位移约束近似表达为桁架截面倒变量的线性函数。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。