周期的模

According to the demand of high magnetic field power supply, reference is increased with a set ramp rate and stops at a set stable value, so reference system is composed of digital setting and digit to analog converting circuit. But the stability of reference is mostly guaranteed by the performance of D/A circuit, so D/A circuit is particularly studied in reference system. The scheme of D/A circuit, the selection of DAC and its voltage reference, hardware anti-jamming design and PCB design are discussed in detail, and software of remote control and PLC are discussed in brief. Zero-flux DC current transformer well satisfies the demands of the high stability of Load current detection unit, so the principle of zero-flux DC current transformer is analyzed; in the mean time a project which detects the long term stability is designed. During 8 hours, analog signal which is detected with high precision digit multimeter is recorded in computer at 1HZ frequency by GPIB communication. The drift error source and related parameters are explained in the compare-amplify part. Detailed subtraction circuit is designed; also amplifier chip and periphery components are selected and verified according to the theory of error analysis.

根据强磁场电源的需求，参考源应按照软件设定的斜率逐渐上升到设定稳态值，则参考源系统应由数字给定和数模转换电路两大部分组成，而参考源的稳定度主要依靠完成数模转换功能的模拟电路的性能来保证，因此本文对参考源系统的研究以数模转换电路为重点，分别从电路方案的确定、数模转换芯片及其基准电压源的选取和验证、电路板硬件抗干扰和PCB设计几方面进行了论述，然后对数字给定部分的远控组态和PLC程序设计作了简要介绍；采用零磁通原理的直流电流转换器很好地满足了对负载电流检测单元高稳定度的需求，本文详细分析了零磁通检测的原理，并在选定此种类型电流转换器的基础上设计了一套检测长期稳定度的方案，8小时内以1秒为采样周期，通过计算机Labview程序和高精度数字电压表的GPIB通讯，将被高精度数字电压表数字化后的模拟信号采样值连续记录至计算机中；比较放大环节简要阐述了漂移产生的原因和相关参数指标，确定了具体的减法电路形式，并根据误差分析理论对运算放大器和外围元器件进行了选取和验证。

The effects of the position and the optical thickness of the defect layer on the defect modes was analyzed.

结果表明，在准周期结构光子晶体引入缺陷，光子晶体禁带中也产生了缺陷模；随着掺杂缺陷层位置和光学厚度的变化，缺陷模的位置和共振透射峰也随之变化。

Fast algorithms.for determining the k-error linear complexity profile of a sequence over GF(2) and GF with period p〓 are proposed, where both 2 and q are primitive root modulo p〓.

给出了计算2元p〓周期序列和q元p〓周期序列k－错复杂度曲线的快速算法，这里2和q都是模p〓的本原根。

Firstly,surd or sonant judgment with each voice frame is done,then the multi-scale wavelet analysis is done only on the sonant frames to get pitches.In order to get accurate pitches,the intervals of local modulus maxima of dyadic wavelet coefficients are corrected according to amplitude information and appearance probability information.

针对这一问题，提出一种基于小波变换的基音周期提取改进算法，将TEO算子与二进小波变换结合起来，首先进行清浊判定，然后只对浊音帧采取多尺度小波分析提取周期，提出用幅度信息和出现概率信息校正二进小波模极大值间距，从而得到准确的周期。

The transmission spectrum of long period grating was analized by a combination of coupled mode theory and transfer matrix method.

用耦合模方法和传输矩阵法相结合对长周期光栅的传输光谱特性进行了研究，提出了用相移长周期光栅使双峰的增益谱线平坦化。

In this paper, based on the knowledge about the change in the microstructures and mechaniacal properties of the cast irons with the influence of temperature, stress and thermo—mechanical circulated load in working cycle of ingot mould, the temperature and stress fields have been analysed by means of thermo-elastic-plastic finitive element, and futher, the behavior of thermal stress factors in every working cycle of the mould have been investigated, by which principles for optimum design of ingot mould's structure has been put out.

本文以钢锭模一个使用周期内的温度场、应力场及热一力循环载荷作用下铸铁的组织结构和力学性能的变化规律为基础。利用热弹塑性有限元法对钢锭模使用过程中的温度场及应力场进行了分析，并进一步研究了钢锭模在每个使用周期间的热应力参数的变化规律，提出了钢锭模结构优化设计的基本原则。

By means of thermo—elastic-plastic finitive element method, the thermo—mechanical loading chart of the ingot mould in working cycle is obtained; with this chart as a control factor, multicycle experiment is carried out on a thermo—mechanical simulater, resembling the circumstance of the real working condition.

即用热弹塑性有限元法获得钢锭模一个使用周期内的热—力载荷谱，在热力模拟实验机上用该热—力载荷谱控制进行多周期模拟实验分析。

Resultantly, the individual warm/cold events in ENSO cycle appear to be partially locked to the annual cycle, and also exhibit obvious irregularity both in amplitude and in lasting time.

本文第四章研制设计了一包含海洋表面边界层和大气辐合反馈过程的热带太平洋海气耦合异常模式，进而利用该模式对ENSO循环进行了较为真实的模拟，通过对模式ENSO循环的演变特征及其形成机制的细致分析，建立了-ENSO循环的非线性分析模式，并提出了ENSO循环形成的一种更为客观的理论，指出：1）和观测事实类似，模式ENSO循环确实涉及了三种主要时间尺度过程即LF、QB和AC，其中LF为3-4年主周期振荡，QB占总方差10～20%；2）ENSO循环的正反馈机制是不稳定海气相互作用过程，且这一不稳定过程的发展在暖态中明显强于冷态；3）ENSO循环的负反馈机制在冷暖态中表现不同，在冷态消亡过程中，这种负反馈过程主要表现为西边界反射产生的时滞效应，但在暖态消亡过程中不存在类似的时滞效应，其负反馈过程主要表现为在海气耦合不稳定充分发展时伴随的赤道两侧冷水上翻过程的加强以及非线性过程的衰减作用抑制了不稳定的发展并最终使得系统回复至冷态；4）ENSO循环的3-4年主周期振荡是一非线性系统的自激振荡现象，其形成是线性系统的本征模即准两年振荡通过非线性机制产生的周期加倍所致，其中&单向性&大气辐合反馈加热过程对其形成至关重要；5）虽然年循环过程对ENSO循环形成没有本质影响，但它可明显影响ENSO循环的具体振幅和位相，使得ENSO对季节循环有明显的&锁相&特征，并且也使得ENSO循环在振幅大小和时间长短方面呈现出明显的不规则性。

A drawing die,a trimming and piercing die and a flanging and restriking die for the precision shaping of the part were designed by using AutoCAD and UGII.

在详细分析车门内板结构及工艺特点的基础上，确定零件的成形工序，以AutoCAD及UGII为辅助工具，设计出车门内板成形所需的拉深模、修边冲孔模和翻边整形模，不仅保证了加工精度，同时也缩短了生产周期，降低了成本。

As a result of flexo business card printing and membership card making machine use rotary-cutting roller die cutting, the highest price, making periods that applies only to live a long version of the sticker short version live the characteristics of high demand.

由于柔性版制卡和会员卡制作机都采用圆压圆模切，模切辊价格高，制作周期长，仅适用于长版活，对于国内不干胶标签短版活需求量大的特点不适应。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了