向轴的

An oscillating lever connected to an engine piston rod and used to transmit power to the crankshaft.

传动杆可摆动的杠杆，与引擎之活塞相连，用以向机轴传送能量

By using volume control method, the basic equations of axial laminar flow for power law fluids in eccentric annuli was seperated and sovled by ADI method.

利用控制体积法对幂律流体偏心环空轴向层流流动的基本方程进行了离散化处理，并用ADI方法进行了求解。

The spray characteristics of three configurations of effervescent atomizers are measured in detail by the MF laser-scattering-analyzer, showing the effects of airliquid ratio, available pressure drop, atomizer geometry and axial distance from exit of atomizer.

这些结果显示了气液比，气液供应压降、喷嘴几何参数、混合腔压力、喷嘴轴向距离等因素对气泡雾化喷嘴喷雾特性的影响。

M were applied to produce six kinds of pure moment of force and to create six kinds of movement of the lumbar spine in flexion, extension, left and right lateral bendings as well as left and right axial rotations.

在双侧小关节分级切除状态下，后路螺纹椎间融合器均能显著降低L4-L5节段的前屈、左右侧弯运动范围，但后伸、左右轴向旋转运动只能恢复到完整状态水平。

After discectomy, partial laminectomy and bilateral medial 1/3 facetectomy, the ROM of L4-L5 segment was significantly increased in flexion, extension, left and right lateral bendings as well as left and right axial rotations (relative ROM 1. 34, 1. 94, 1. 19, 1. 34, 2. 23, 1. 52 seperatively).

随着双侧小关节逐级切除，各组运动的运动范围明显呈逐渐增加趋势，双侧小关节内侧1/3切除和双侧小关节全切除状态之间在前屈、左右侧弯、左右轴向旋转运动方面有显著性差异。

Satisfies wide range of positioning,pivot and alignment application, chamfered and makes mating hole location easily.

应用于安装板有位置排列、轴向定位要求的场合，尾部大倒角使安装更快捷。

The kiln body is divided into two sections of electrical furnace body and dynamic rotation with the kiln body constructed of clayed circular hearth uniformly inserted with 9 silicon carbon rods along the circular axis( one group made up of 3 rods and Y connection for every 3 groups).

窑体部分又分为电炉炉体和动力转动两部分，炉体部分采用粘土质圆形炉膛，沿圆轴向均匀插9根硅碳棒（每三根串联成一组，三组按& Y &接线）高铝质的陶瓷炉管又置于硅碳棒内周，通电后硅碳棒产生高温，加热炉管。

At the same time, line up buyers of real estate are quietly changing, showing the past, inner ring, in the Link as the central axial expansion of the outer ring of regional trends.

与此同时，排队购买房地产正悄悄地发生变化，显示过去，内环，在链接为中心轴向扩大外环区域的趋势。

The plunge-cut method, in which grinding is achieved through the cross feed of the grinding wheel and no axial feed is applied.

插入-切削方法：这种方法通过砂轮的横向进给完成磨削而不采用轴向进给。

Is the circular parts, for the two bearing rings, or bearing washer, or between two and a half or two and a half between the bearing ring between the bearing washer in order to maintain between them under the axial distance.

是环形零件，用于两个轴承套圈或轴承垫圈之间或两半轴承套圈之间或两半轴承垫圈之间以使它们之间保持所规定的轴向距离。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。