向轴的

The results of XRD,TEM and Mossbauer effect show that underpressure,the orientation of acicular particles were redistri-buted,that is,the long axis tend to perpendicular to the direc-tion of the pressure.

X-ray衍射、穆斯堡尔谱和TEM的研究表明，在压力的作用下，针形颗粒产生了取向的重新分布，即长轴方向倾向垂直于压砧轴向。

While with the Coriolis force omitted, the flow in the cavity is under the influence of centrifugal buoyancy force, which can develop from stable to unstable as this force enhances. The centrifugal buoyancy force could lead to flow unstably.

哥氏力垂直于〓与〓构成的平面，对径向速度导致切向作用力，对切向速度导致径向作用力，在该力的作用下盘腔内轴向通流诱导的旋涡被压扁，尽管涡强有所增加，但是盘面的平均换热基本减弱。

The process of denting and the lateral load has been studied under different end conditions and axial pressure of different levels.

研究了在不同边界条件和初始轴向压力水平下，圆管构件的凹坑损伤形成过程和侧向承载力。

Results A series of data were gained of geometrical morphology and relative area of smooth muscle cells,elastin and collagen in axial and circumferential directions of the ascending aorta and aortic arch.

结果 获得了人升主动脉-主动脉弓几何形态和显微结构成分含量沿轴向和周向连续变化的完整数据。

And in this process the torsional rigidity of the cross axle type universal shaft was found having great impacts on the torsional vibration of the main transmission system.

在进行轧机主传动系统的扭振分析时，发现十字轴式万向联轴器的扭转刚度对主传动系统扭振的影响十分巨大。

Based on this discovery this dissertation presented that the torsion rigidity of the cross axle type universal shaft must be taken into account when researching the main transmission system of the rolling mill.

并依此提出了在研究轧机主传动系统的扭转振动时，必须计及十字轴式万向联轴器的扭转刚度的观点。

I design two axis which taper is 1:12 to install bearing and fix bearing of cylindrical roller, I used locking nut to fix the direction of bearing owing to the reason of boring head's high precision.

主轴中设计了两个锥度为1：12的的轴段用于安装支承和固定圆柱滚子轴承，由于镗削头的精度要求很高，在轴承处使用了锁紧螺母进行轴向固定。

In the components two jaw spot has two mm holes, with installs rolls the real bearing and is connected with the cross axle, plays the rotary shaft coupling role.

零件的两个叉头部位上有两个Φ mm 的孔，用以安装滚真轴承并与十字轴相连，起万向联轴节的作用。

In design of movable forming machine of pipe thread,adopt that there is not shaft redactor,cutting tool rotate,pipe axial feed operate mode.

在可移式管螺纹成型机设计中，采用了无轴式结构的减速器和螺纹梳刀旋转、管件轴向进给的工作方式，实现非直线圆管螺纹的成型加工。

In the boreal summer, there are two STH ridge lines in mid-Pacific separated by the mid-Pacific trough, of which the north part (call as mid-Pacific STH ridge line) is joined with the west Pacific STH, and the south is belonged to the North America STH. The structure of them is winter pattern that the ridge axis slopes southward against height. Litter differences lie in vertical circulation structure of the steady and instantaneous mid-Pacific STH, and descent flow exists around ridge axis.

北半球夏季，中太平洋地区中高层存在双副高脊线，其中偏北的一条与西太平洋副高相连，偏南的一条系北美副高西伸脊线，其间为洋中槽；副高结构表现为冬季型，即高压脊轴随高度向南倾斜；中太平洋副高垂直环流的定常结构与瞬时结构差别不大，副高脊轴附近均有下沉气流存在。

According to the clear water experiment, aeration performance of the new equipment is good with high total oxygen transfer coefficient and oxygen utilization ratio.

曝气设备的动力效率在叶轮转速为120rpm～150rpm时取得最大值，此时氧利用率和充氧能力也具有较高值。

The environmental stability of that world - including its crushing pressures and icy darkness - means that some of its most famous inhabitants have survived for eons as evolutionary throwbacks, their bodies undergoing little change.

稳定的海底环境─包括能把人压扁的压力和冰冷的黑暗─意谓海底某些最知名的栖居生物已以演化返祖的样态活了万世，形体几无变化。