向轴的

In this thesis, the Finite Element Method is applied to the solution of the Laplace equation formulated by means of stream function for the calculation of the static hydraulic thrust.

本文通过有限元法求解用流函数表示的拉普拉斯方程，进而计算轴流式机组的静态轴向水推力。

The result of the limit element analysis validates the analysis of the mechanics about the double punch.

从本次试验结果来看，径向压裂和轴向压裂法的试验值比较接近，结果低于单轴拉伸试验，土梁弯曲法的

Impeller with static balance is fixed onto the shaft by the sleeve and the sleeve nuts on the two sides. Its axial position may be adjusted through sleeve nut.

经过静平衡校验的叶轮，用轴套和两边的轴套螺母固定在轴上，其轴向位置可通过轴套螺母进行调整。

Parts the first part of the two forks, there are two holes for the installation of needle bearings and connected with the cross-axis, since the role of universal coupling.

零件的两个叉头部位上有两个孔，用以安装滚针轴承并与十字轴相连，起万向联轴节的作用。

Based on parameters analysis and calculated figures of rolling mill drive system, we analyze broken causation of this kind universal joint shaft first made in China.

通过对小H型钢轧机传动系统的参数分析和计算数值，来分析轧机万向接轴在首次国产化过程中十字轴断裂频繁以及花键卡死的原因。

The hooping mechanism of the CFST member was analyzed by using energy principle and minimum potatial energy principle .

利用修正弹性模量的方法来计入内填式钢管混凝土轴压构件承载力的提高，并用能量法和最小势能原理从中导出了在轴向压力作用下内填式钢管混凝土构件受箍机理。

The long axis of the high intensity isoseism of this earthquake is NE-trending, consistent with the Haiziyan Fault, which is therefore assumed to be the seismogenic fault of this earthquake.

五原6.0级地震高烈度区等震线长轴呈NE向，与海子堰断裂一致，是五原地震的发震构造。1996年包头西6.4级地震发生在由陡崖和沟槽地貌显示的NEE向乌拉山北缘断裂与NW向新生砂石厂断裂交会的部位。

Axial-Flow Fans. This type of fan is designed to cause air to flow parallel to the fan axis.

轴流风机：这种类型的风机设计使空气平行于风机的轴向流动。

Test result makes clear, install rate matching steel to be the core profiled bar of 2.88%, the axial pressing intensity of test specimen can rise about 30%, axial is out of shape ability can raise about 1 times.

试验结果表明，设置配钢率为2.88%的核心型钢，试件的轴压强度可提高约30%，轴向变形能力可提高约1倍。

Additionally, cross section curve of helix wire, contact radius, clearance angle, width and ratio in wires same layer were obtained.

为了掌握轴向载荷下螺旋钢丝的变形特性以合理设计钢丝绳，推导了螺旋钢丝轴应变显式表达式，给出了螺旋钢丝截面曲线表达式和同层螺旋钢丝正好满足接触时钢丝的半径及接触半径、间隙角、间隙值和间隙率表达式。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。