向轴的

Axial elongation of inner isodiametric cells of the globular somatic embryo followed by the change in the growth axis of the procambium was an important event in heart-shaped or oblong-stage somatic embryo.

球形胚内部等径细胞轴向延长，接着前形成层生长轴发生变化，这些是心形胚或椭圆形体胚中的重要事件。

Continuous beam models with spring supports were set up to model end-plate connections. By comparing the results from tests with those from model analysis, the following conclusions can be drawn: during loading process, the neutral axis moves from the centroid axis to compression zone, not exceeding the center line of bolts inside the compression flange; ultimately, the tension flange and end-plate can be simplified as T-stub on the assumption that the axial forces of bolts in tension zone are equal to each other.

理论计算系建立带弹性支座的连续梁模型模拟端板连接，将模型计算结果与试验结果比较分析，结果表明：加载过程中，螺栓群中和轴逐渐从其形心轴向受压区移动，但不超过受压翼缘内侧螺栓中心线；极限状态下，受拉翼缘和端板可简化为等效T型件。

Each subject performed three different PA glide techniques (PA glide with the thumb unsupported, PA glide with digital support and the PA glide with IP supported by the index) on a force plate while interphalangeal, metacarpophalangeal and carpometacarpal joints kinematics were tracked by a motion analysis system. The joint angles, maximum thumb-tip force, surface EMG activities of 8 thumb muscles and the Beighton score of each subject were recorded for analyses.

每位受试者在六轴力版上表现3 种不同的后前向滑动徒手技巧(不支撑后前向滑动，四根手指支撑之后前向滑动，大拇指指间关节支撑之后前向滑动)，藉由动作分析系统同步收取IP 关节、MCP 关节及CMC 关节动力学资料，每个大拇指关节角度、指尖的力量、8 块大姆指肌肉的表面肌电图以及每位受试者的柔软度分数。

Orebodies occur in a fault near the axial region in the southern limb of the Jinjinghe-Hujiamiao inverted secondary anticline in the southern limb of the Hongyansi-Heishan composite syncline. Host rocks are dolomitic rocks in the middle and upper parts of the Devonian Qingshiya Formation. Their spatial distribution is obviously controlled by an interlayer fracture-fissure zone near the axial region in the steeply dipping southern limb of an anticline. Ores are dominantly of nodular and stockwork types and the feature of epigenetic mineralization is very pronounced.

矿体产于红岩寺—黑山复式向斜南翼金井河—胡家沟次级背斜南翼近轴部断裂中，赋矿岩石为泥盆系青石垭组中上部白云质岩，其空间展布明显受背斜陡倾南翼近轴部的层间断裂-裂隙带构造控制，矿石主要有团块状和网脉状，其后生成矿现象非常明显。

The torsional distortion and the torsional rigidity of the cross axle type universal shaft are calculated by using the three-dimensional finite elements method.

运用三维有限单元法对十字轴式万向联轴器的扭转变形和扭转刚度进行了分析计算。

Check if the above still does not resolve, you can check the pump apart to see whether the broken shaft, but also check the pump ring, stationary ring is intact, the possibility of a small amount of rotor axial movement.

通过以上检查若仍不能解决，可将泵拆开检查，看泵轴是否折断，还应检查泵的动环、静环是否完好，整个转子可否少量轴向移动。

Flap valve pin and WA44C Type Pound-Grade Balance Bellows Spring-Loaded Safety Valvevalve shaft axial clearance between the bearing face not less than 0.25mm.

阀瓣轴销与阀体支承端面之间的轴向间隙不应小于0.25mm。

Flap valve pin and WA44C Type Pound-Grade Balance Bellows Spring-Loaded Safety Valve valve shaft axial clearance between the bearing face not less than 0.25mm.

阀瓣轴销与阀体支承端面之间的轴向间隙不应小于0.25mm。

The results show that the tangential velocity distribution in the annular space shows a typical feature of strongly swirling flows and it consists of quasi-free vortex area and quasi-forced vortex area.

由于流体与双侧壁面之间的摩擦造成能量损失和湍流能量耗散，导致最大切向速度不断衰减且位置沿轴向向下逐渐向提升管外壁移动，同时涡量传递造成外部的准自由涡区逐渐增大，内部的准强制涡区逐渐缩小。

First of all, horizontal swing to solve big problems, re-allocation of a motor sleeve (with the bronze with stent hole so), so that the electrical sleeve just in bronze wall bracket can rotate, reducing the gap; further axial movement to solve the problem with the motor shaft with Hexagon Hexagon washer so thick 0.6mm.

首先解决横向摆动大的问题，重新配做一个电机轴套，使电机轴套在铸铜支架内壁刚好能转动，减小间隙；再解决轴向窜动问题，与内六角电机轴配做内六角垫圈，厚0.6mm。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。