向轴的

The results showed that the buckling in the plane perpendicular to the axle is the reason for the super high anisotropy.

结果表明纳米管束在垂直于轴向的面内屈曲是造成面内模量远小于轴向模量的主要原因。

The axial runout of the commercial disc is about 300 μm. The equalizer used in this study was designed for 500 μm.

一般市售碟片的轴向摆动约为300 μm，本研究将轴向摆动之范围提高到500 μm，来设计所需要的等化器。

In order to make cross joint type universal coupling long service life , puts forward setting up the torque examining system to control the torque, inspecting the position of input and output equipment to control the space position of the coupling and reduce the influence of additional force moment and control ling the balance force and the bearing clearance and so on, to avoid the coupling premature failure or shattering of the coupling.

为使十字轴式万向联轴器长寿命服股，提出了设置转矩测试系统控制转矩；通过监测输入及输出设备的位置控制联轴器的空间位置，以减少附加力矩的影响；控制平衡力及轴承间隙等技术控制措施，避免联轴器过早失效或损坏。

The rebuilding of universal joint for 3200mm four-high roughing mill is introduced and analyzed in this paper.

本文介绍了中厚板厂3200mm四辊粗轧机万向联轴器的改造过程，并对其进行分析，这对于提高中厚板轧机万向联轴器的承载能力具有重要意义。

The prominence of localizer can induce a certain error of 2％ approximately, which was adjusted in the frontal images.

定位器的突出造成一定程度的轴向误差，约为2％，我们对正面图像进行了轴向误差校正。

The fractal dimension and tortuosity of trajectory are analyzed. The method of calculating the fractal dimension of trajectory is developed.

分析了孔道轴向分形维数与孔道空间曲折性的关系，建立了关联色谱固定相内孔道轴向分形维数的计算式。

Non-mainstream platform-based peripherin-small size, most of the adoption of the platform-based CTP photoptic, and the third corrosionbehaviorstudy of light source as described in the axis moved in different ways, but the plates move in x axis, the light source to the y axis on the other side by side to do, in collaboration with wirelike scan x axis mobile photoptic surface, forming the rotating linggong microscopic mobile, multiple ligtht section exposure, less mobile components.

否干不源的平台式感平小尺寸CTP，不小众拔取平台式感平，但是和第不一项所述块状平源XY轴都安放的方法差别，而是印版以X轴安放，平源以Y轴由一背向另一背怠工线状扫描，打扰X轴安放酿成感平背，有的采回旋扭转凌镜安放，有的采众平速区段曝平的差别，安放元件较少。

Under the condition of poor effect of surmounting "statics with pitch-resistant",domestic scholar have made new concept —deviation control with high WOB .

大钻压动力防斜技术增加钻压引起钻柱屈曲，保特钻柱涡动，有井斜时使钻柱产生周期性变化的轴向附加力，无井斜时轴向附加力消失，克服了传统防斜技术中吊打的缺点，提高了钻井速度，达到了解放钻压的目的。

The aerostatic bearing levitates the actuating rod with four radial air inlets on each side. The frictionless aerostatic guide can improve the actuating rod is electromagnetically driven by a fixed solenoid and a actuating solenoid. Through adjusting the axial position of the actuating solenoid, the actuating stroke can be fine regulated.

双列径向供气之气静压轴承提供致动轴作径向的支撑，其低摩擦之特性有助於提升定位精度，致动轴两端外侧设有固定线圈与致动线圈，调整致动线圈轴向位置可以改变致动器最大行动范围。

First, systematic study on propagation, reflection and interaction of axial stress wave is made to deduce the calculation equation for axial elastic and plastic stress wave, which fit for analysis of impact buckling of axial compression member.

本文首先对轴向应力波在构件中的传播、反射及相互作用进行系统分析，推导出适合轴心受压构件冲击屈曲分析的轴向弹、塑性应力波计算公式。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。