向轴的

The conclusions obtained are applicable for active accelerating and passive decelerating parts of trajectory as we...

在小推力和小轴向过载的情况下，各种不同的计算方法所得的结果相差不大。

The distribution and variation of plastic zone in the joint were calculated and analyzed during inertia friction welding process. And the variation of deformation rate of plasticized material was also simulated.

计算并分析了惯性摩擦焊接过程中接头塑性区的分布、扩展规律及其与工件轴向缩短的关系，并计算了塑性区金属塑性变形速率的分布和变化情况。

The conducting wall in micro-tube preheats the inlet mixture by axial heat transfer. The existence of conducting wall will help to reach full reaction in the micro-tube. As the inlet velocity increases, both the existence of the surface catalytic combustion and the gas phase combustion become the limiting factors on combustion. Wall material and equivalence ratio of hydrogen/air mixture have important influence on catalytic combustion of hydrogen.

计算结果表明：表面催化反应对空间气相反应有抑制作用；在微型管道内，通过导热壁轴向间的传热，预热入口混合气体，使氢气燃烧更加充分；随着入口速度的增大，燃烧过程同时存在着表面催化反应和空间气相反应两种控制因素；管壁材料和当量比对氢气的催化燃烧过程有重要的影响。

Now the list type friction clutch quite consummates in thestructural design aspect Uses has axial elastic enhancedthe coupling joint smoothness Clutch driven disk always becomes theChinese dress to have the torque shock absorber, had prevented thetransmission system reverse resonated, reduced the noise andmoves the load.

如今单片干式摩擦离合器在结构设计方面相当完善。采用具有轴向弹性的从动盘，提高了离合器的接合平顺性。离合器从动盘总成中装有扭矩减震器，防止了传动系统的扭转共振，减少了传动系噪声和动载荷。

Moreover, based on the uniformity of solid axial distribution, the respective performances of the radiant orifice gas distributor and the perforated plate （1 mm） were compared, as well as with and without internals.

从固体轴向分布的均匀性分别比较辐射式锐孔气体分布器和1mm多孔板气体分布器的性能以及有／无内部构件的性能。

DIS has continued to develop its isolators to perform well at large lateral displacements accompanied with high axial loads.

DIS继续开发它的免震支座使它很好地做到在带有高度轴向负荷的情况下进行大的横向位移。

By experimental work and theoretical analysis, the author investigated the principle of knitting biaxial wefts knitted fabrics and knittability on flat knitting machine, This part analyzes the influence of yarn tension, taking down force, pulling down depth in detail.

通过实验研究和理论分析，文中探讨了纬编双轴向织物的编织原理和在横机上的可编织性，分析了弯纱深度、给纱张力、牵拉力对编织的影响。

For the case of deep oil well, pumping rod is eccentric in oil tube during the oil recovery.

在采油过程中，由于油井较深的缘故，抽油杆在油管中是处于偏心位置的，聚驱井产出液在抽油杆做轴向运动的井筒中的流动问题就是非Newton流体在内管。。。

E. , semiconfocal, halfconcentric and plane-parallel geometries, and the mode properties and discrimination are studied by analyzing the coupling losses.

结果表明：当环间隙间距与其中心半径的比值较小时，在同轴波导激光器中的低阶振荡模是环向极化的。

This method connects the input and output of the neural network with mechanical sizes of the wire rope and the tester and increased the axial testing resolution. This method was proved to be available by a few examples.

该方法将网络的输入和输出与钢丝绳结构尺寸和探头结构尺寸联系在一起，提高了轴向检测的分辨率，在实例分析中证明了它的有效性和正确性。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。