后齿轮

Never seat or back seat the valve using an air wrench; manually seat and back seat the valves with caution, especially when equipped with bevel gears.

没有阀座或后座的阀门采用气动扳手；手动阀座和后座阀门操作要小心，特别是在配置伞齿轮操作机构后。

The conveyed medium can't be leaked outside. Thus it will not cause the environmental pollution and human body safety dangerous while exhausting the toxin and flammable or corrosive medium. 5、No electricity. It's safe and reliable while using in the flammable and explore places. 6、It can be soaked in medium. 7、It's convenient to use and reliable to work. Only open or close the gas valve body while starting or stopping. Even if no medium operation or pausing suddenly for long time because of accident matters, the pump will not be damaged caused by this. Once over-loading, the pump will automatically stop and possesses the self-protection function. When the load recovers normally, it also can start automation. 8、Simple structure and less wearing parts. This pump is simple in structure, installation and maintenance. The medium conveyed by the pump will not touch the matched pneumatic valve and coupling lever etc. not like other kinds pumps, the performance will drop down gradually because of the damages of rotor, gear and vane etc. 9、It can transmit the adhesive liquid (the viscosity is below 10000centipoise) 10、 This pump needn't the oil lubricant. Even if idling, it has any influence to the pump. This is a characteristic of this pump.

所以抽送有毒、易挥发或腐蚀性介质时，不会造成环境污染和危害人身安全； 5、不必用电，在易燃、易爆场所使用安全可靠 6、可以浸没在介质中工作 7、使用方便、工作可靠、开停只需简单地打开和关闭气体阀门，即使由于意外情况而长时间无介质运行或突然停机，泵也不会因此而损坏，一旦超负荷，泵会自动地停机，具有自我保护性能，当负荷恢复正常后，又能自动启动运行； 8、结构简单、易损件少，该泵结构简单，安装、维修方便，泵输送的介质不会接触到配气阀，联杆等运动部件，不像其他类型的泵因转子、活塞、齿轮、叶片等部件的磨损而使性能逐步下降； 9、可输送较粘的液体（粘度在1万博以下）； 10、本泵无须用油润滑，即使空转，对泵也无任何影响，这是该泵一大特点

In the left tool carriage, the ball leadscrew、the servo motor and single gear reducer were displaced,and the coordinated movement about X and Z axis could be implemented by semi-closed loop control of SINUERRIK 802D numerical system.

左刀架采用滚珠丝杠、伺服电机和一级齿轮减速，并利用SINUMERIK 802D数控系统的半闭环控制实现左刀架的X轴和Z轴联动控制，机床改造后，大大扩大了机床的加工范围，同时提高了生产效率和加工精度。

The front end parts include front casing, pedestal, driving shaft assembly, percussion shaft assembly, sliding gear assembly, sliding board, spring, eccentric pin, cam and knob.

它包括前端部件和后端部件；前端部件包括前端壳体，底座，传动轴组件，冲击轴组件，滑动齿轮组件，滑板，滑板弹簧，偏心销，凸轮，旋钮。

The first to use PRO / E software components establishment of the body (body, cylinder head, cylinder pad, cylinder liner, the main bearing caps, Flywheel carcasses, gear Connection Board Room, Shell pump, oil pan, about mounting frame, rear axle oil blocks, etc.) 3D solid model; Then use Hypermesh software division finite element mesh to ensure a good grid quality, and better coordination of the grid between quantity and accuracy of contradictions; Finally using ANSYS software components of a body finite element analysis.

首先利用PRO/E软件建立机体组件（机体、气缸盖、气缸垫、气缸套、主轴承盖、飞轮壳、齿轮室连接板、水泵壳体、油底壳、左右悬置支架、后轴油封盖等）的三维实体模型；然后利用Hypermesh软件划分有限元网格，保证了良好的网格质量，较好地协调了网格数量和计算精度之间的矛盾；最后利用ANSYS软件对机体组件进行了有限元分析。

In order to solve the problem that the hardness of bevel drive gear screw after heat treatment cannot reach the requirement of technology,a series of heat treatment process tests have been conducted.

为解决热处理后主动圆锥齿轮尾部螺纹硬度达不到技术要求的问题，进行了几种热处理工艺试验。

The helical gear transmission system which is one important component of marine shafting has been widely applied in marine power plant.

斜齿轮传动系统广泛应用于船舶动力装置中，是船舶轴系后传动部件之一。

Resorting to the Roberts-Chebyshev theorem,we replace the two cranks of a crank-rocker cognate mechanism with a double bar,which is required to satisfy certain geometrical and motion conditions,and we change the mechanism thus reformed into a geared five-bar mechanism so that one of its links can fully rotate with the link connected with it.

借助于Roberts-Chebyshev定理，将曲柄摇杆轨迹同源机构的两曲柄分别用一双杆组代替，并要求双杆组满足一定的几何尺寸条件和运动条件，使变形后的机构为齿轮五杆机构，且满足机构的一个连架杆以及与其相连的连杆能够整周转动。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。