后齿轮

However, when the tractor is heavily repaired or when it is replaced with a new pair of central driving gear or cone bearing, careful adjustments must be carried out to guarantee right tooth clearance and tooth flank imprints at the same time

但在拖拉机大修后或更新一对新的中央传动齿轮或锥轴承时，则必须进行仔细的调整，同时保证齿侧间隙和齿面印痕。

And irregular inside and outside the cavity of the chamfered edge, especially for large parts of the chamfered edges of some songs the general machinery can not be processed, using hand-held circular chamfering machine chamfering the convenient and fast.

本文是对手持圆弧倒角机的研究，主要通过对倒角机的电机的选择、齿轮各个参数的选定、传动轴材料强度的要求等几个方面的计算确定设计方案是否可行，并在确定可行性方案后把手持圆弧倒角机的结构设计的紧凑、轻巧、操作方便。

High-frequency heat treatment after the durable, do not wear gear.

高频热处理后坚固耐用，齿轮不会磨损。

Ases change use behind annular gear knife rest, can as point shape knife or a dish of shape piece of milling cutter process in tooth.

当换用内齿轮刀架后，能以指形刀或盘形片铣刀加工内齿。

Considering of helical gear separate mesh and tooth-back shock, the non-linear vibration equitions of the system are also established, and the non-linear stable cycle solutions of the equitions are evaluated through dividing the timechanging stiffness matrics and dimension the equitions with selfadapt vary-step auto-RK4 numerical method.

考虑了斜齿轮传动的轮齿脱啮和齿后侧冲击，建立了系统的非线性振动方程，并通过对方程时变刚度阵的分块处理及无量刚化，用自适应变步长auto-RK4数值方法求出了系统非线性振动方程的稳态周期解。

Spear fishermen also exploited the giant sea bass, first as free divers, and then after the mid 1950s using scuba gear.

枪渔民还利用了巨大的海低音，为免费的潜水夫的第一次，然后后於五十年代使用潜水齿轮。

Each rear car wheel has a separate axle , and there are two side gears splined to the inner ends of the two wheel axle s.

每个后车轮都有一个独立的车桥，两个半轴齿轮用花键与两个车轴的内端相连。

While a ball mill is working, balls in the mill are lifted, and then are thrown away with a certain velocity to collide raw material. But at the same time, balls and underboarding are also got collision which may make balls and underboarding fracture. Considering the tough lubrication condition and dust and prills have easy access to meshing zone of gears, the heavy abrasion on gear surface often appears in the upstage gear of open-gear transmission of ball mill.

当球磨机正常运转时，磨球被提升到一定高度后抛落，以一定的速度对物料产生冲击而粉碎物料，同时也对磨球和衬板自身产生冲击，这可能造成磨球和衬板的破球磨机的末级开式齿轮传动，由于润滑条件差，粉尘、金属颗粒容易进入啮合区，齿面常常出现严重磨损，导致齿廓形状发生变化，最后因齿厚磨损过多而折断。

The universal powder box includes one box with powder bin and cover, one stirrer inside the powder bin, one powder feeding roller in the outlet of the powder bin, one developing roller contacting with the powder feeding roller and one locking device for the powder box to be set in and taken out from the sensitive drum. The cover has one upper planar surface, and after being installed, the plane is located below one corresponding raised edge of the printer. In the roller end gear combination outside one side wall of the box, there are two with driving force driving position.

包括一个带有粉仓的盒体和盖，位于粉仓内的搅拌装置，一个位于粉仓出口处的送粉辊、一个与送粉辊接触的显影辊，及使粉盒能顺利置入或取出感光鼓盒的锁放装置，盖的上表面基本是一个平面，装机后该平面位于打印机对应盖下表面凸起的下缘之下，在盒体一个侧壁外的各辊端齿轮组中，有两个带有动力受口的驱动位。

For cutting the composite lock gear with unequal tooth thickness, a study is made on the design method of gear sharper cutter with nonstandard parameter involute tooth profile and noninvolute tooth profile. The cutter tooth arrangement, the choice of teeth number of the cutter and the basic method of cutter design are discussed; and a new method of choosing deflection factor by using limited area is presented.

研究加工不等齿厚的非标准参数渐开线齿形，与非渐开线齿形复合的锁闭齿轮插齿刀刀齿的排列、刀具齿数的选择以及刀具设计的基本方法，介绍用限制区域选择插齿刀变位系数的新方法，并给出刀具齿顶后角与侧螺旋角的关系曲线，为插齿刀参数的选择提供依据。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。